Serial port (NSA325)

From NAS-Central Zyxel Wiki
Jump to: navigation, search

Contents

Hardware

The NSA325 has a 3.3V TTL serial port
Nsa325 serial port.jpg
Pinning:

          +----+----+           
          |    |    |
+----+----+----+----+----+
|3.3V| TX | RX |    | GND|
+----+----+----+    +----+

You can´t connect this directly to an RS232 port, you need a TTL level convertor, or something like a FTDI TTL-232R-3V3.

Settings

115200 baud, no parity, 8 data bits, 1 stop bit, no handshake.

Bootlog

(firmware 4.50, no network connected, packages BackupPlanner, Gallery, NFS, PHP-MySQL-phpMyAdmin an pyLoad installed):

ü
         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_ 
| | | |___|  _ \ / _ \ / _ \| __| 
| |_| |___| |_) | (_) | (_) | |_ 
 \___/    |____/ \___/ \___/ \__| 
 ** MARVELL BOARD: DB-88F6282A-BP LE 

U-Boot 1.1.4 (Jun 14 2011 - 21:40:09) Marvell version: 3.5.9

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00

Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz 

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 512MB 
DRAM Total size 512MB  16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)
Kernel address is 0x4640000.

Streaming disabled 
Write allocate disabled


USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  2 ��� 1 ��� 0 

NAND read: device 0 offset 0x4640000, size 0xa00000

Reading data from 0x4640000 --   0% complete.
Reading data from 0x4659800 --   1% complete.
Bad block at 0x4660000 in erase block from 0x4660000 will be skipped
Reading data from 0x4693000 --   2% complete.
Reading data from 0x46ac800 --   3% complete.
Reading data from 0x46c6000 --   4% complete.
Reading data from 0x46df800 --   5% complete.
Reading data from 0x46f9800 --   6% complete.
Reading data from 0x4713000 --   7% complete.
Reading data from 0x472c800 --   8% complete.
Reading data from 0x4746000 --   9% complete.
Reading data from 0x475f800 --  10% complete.
Reading data from 0x4779800 --  11% complete.
Reading data from 0x4793000 --  12% complete.
Reading data from 0x47ac800 --  13% complete.
Reading data from 0x47c6000 --  14% complete.
Reading data from 0x47df800 --  15% complete.
Reading data from 0x47f9800 --  16% complete.
Reading data from 0x4813000 --  17% complete.
Reading data from 0x482c800 --  18% complete.
Reading data from 0x4846000 --  19% complete.
Reading data from 0x485f800 --  20% complete.
Reading data from 0x4879800 --  21% complete.
Reading data from 0x4893000 --  22% complete.
Reading data from 0x48ac800 --  23% complete.
Reading data from 0x48c6000 --  24% complete.
Reading data from 0x48df800 --  25% complete.
Reading data from 0x48f9800 --  26% complete.
Reading data from 0x4913000 --  27% complete.
Reading data from 0x492c800 --  28% complete.
Reading data from 0x4946000 --  29% complete.
Reading data from 0x495f800 --  30% complete.
Reading data from 0x4979800 --  31% complete.
Reading data from 0x4993000 --  32% complete.
Reading data from 0x49ac800 --  33% complete.
Reading data from 0x49c6000 --  34% complete.
Reading data from 0x49df800 --  35% complete.
Reading data from 0x49f9800 --  36% complete.
Reading data from 0x4a13000 --  37% complete.
Reading data from 0x4a2c800 --  38% complete.
Reading data from 0x4a46000 --  39% complete.
Reading data from 0x4a5f800 --  40% complete.
Reading data from 0x4a79800 --  41% complete.
Reading data from 0x4a93000 --  42% complete.
Reading data from 0x4aac800 --  43% complete.
Reading data from 0x4ac6000 --  44% complete.
Reading data from 0x4adf800 --  45% complete.
Reading data from 0x4af9800 --  46% complete.
Reading data from 0x4b13000 --  47% complete.
Reading data from 0x4b2c800 --  48% complete.
Reading data from 0x4b46000 --  49% complete.
Reading data from 0x4b5f800 --  50% complete.
Reading data from 0x4b79800 --  51% complete.
Reading data from 0x4b93000 --  52% complete.
Reading data from 0x4bac800 --  53% complete.
Reading data from 0x4bc6000 --  54% complete.
Reading data from 0x4bdf800 --  55% complete.
Reading data from 0x4bf9800 --  56% complete.
Reading data from 0x4c13000 --  57% complete.
Reading data from 0x4c2c800 --  58% complete.
Reading data from 0x4c46000 --  59% complete.
Reading data from 0x4c5f800 --  60% complete.
Reading data from 0x4c79800 --  61% complete.
Reading data from 0x4c93000 --  62% complete.
Reading data from 0x4cac800 --  63% complete.
Reading data from 0x4cc6000 --  64% complete.
Reading data from 0x4cdf800 --  65% complete.
Reading data from 0x4cf9800 --  66% complete.
Reading data from 0x4d13000 --  67% complete.
Reading data from 0x4d2c800 --  68% complete.
Reading data from 0x4d46000 --  69% complete.
Reading data from 0x4d5f800 --  70% complete.
Reading data from 0x4d79800 --  71% complete.
Reading data from 0x4d93000 --  72% complete.
Reading data from 0x4dac800 --  73% complete.
Reading data from 0x4dc6000 --  74% complete.
Reading data from 0x4ddf800 --  75% complete.
Reading data from 0x4df9800 --  76% complete.
Reading data from 0x4e13000 --  77% complete.
Reading data from 0x4e2c800 --  78% complete.
Reading data from 0x4e46000 --  79% complete.
Reading data from 0x4e5f800 --  80% complete.
Reading data from 0x4e79800 --  81% complete.
Reading data from 0x4e93000 --  82% complete.
Reading data from 0x4eac800 --  83% complete.
Reading data from 0x4ec6000 --  84% complete.
Reading data from 0x4edf800 --  85% complete.
Reading data from 0x4ef9800 --  86% complete.
Reading data from 0x4f13000 --  87% complete.
Reading data from 0x4f2c800 --  88% complete.
Reading data from 0x4f46000 --  89% complete.
Reading data from 0x4f5f800 --  90% complete.
Reading data from 0x4f79800 --  91% complete.
Reading data from 0x4f93000 --  92% complete.
Reading data from 0x4fac800 --  93% complete.
Reading data from 0x4fc6000 --  94% complete.
Reading data from 0x4fdf800 --  95% complete.
Reading data from 0x4ff9800 --  96% complete.
Reading data from 0x5013000 --  97% complete.
Reading data from 0x502c800 --  98% complete.
Reading data from 0x5046000 --  99% complete.
Reading data from 0x505f800 -- 100% complete.
 10485760 bytes read: OK
## Booting image at 02000000 ...
   Image Name:   Linux-2.6.31.8
   Created:      2012-07-26   4:29:44 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    6108928 Bytes =  5.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux.......................................................................................................................................................................................................................................................................................... done, booting the kernel.
Linux version 2.6.31.8 (root@Neo) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #2 Thu Jul 26 12:29:20 CST 2012
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 130048
Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
PID hash table entries: 2048 (order: 11, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512MB = 512MB total
Memory: 506368KB available (5384K code, 302K data, 3164K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 1599.07 BogoMIPS (lpj=7995392)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
invoking softwareStaggeredSpinUp()..., it will delay 5 seconds to spin up the second harddisk

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 512MB 
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB 
PEX0_IO ....base f2000000, size   1MB 
PEX1_MEM ....base e8000000, size 128MB 
PEX1_IO ....base f2100000, size   1MB 
INTER_REGS ....base f1000000, size   1MB 
NFLASH_CS ....base fa000000, size   2MB 
SPI_CS ....base f4000000, size  16MB 
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size   2MB 

  Marvell Development Board (LSP Version KW_LSP_5.1.3_patch18)-- DB-88F6282A-BP  Soc: MV88F6282 Rev 1 LE

 Detected Tclk 200000000 and SysClk 533333333 
Marvell USB EHCI Host controller #0: d003a740
	[BlueDBG] reseting SoC Pex[0]  0 ...
PEX0 interface detected Link X1
	[BlueDBG] reseting SoC Pex[1]  0 ...
	[BlueDBG] reseting SoC Pex[1]  1 ...
	[BlueDBG] reseting SoC Pex[1]  2 ...
	[BlueDBG] reseting SoC Pex[1]  3 ...
	[BlueDBG] reseting SoC Pex[1]  4 ...
	[BlueDBG] reseting SoC Pex[1]  5 ...
	[BlueDBG] reseting SoC Pex[1]  6 ...
	[BlueDBG] reseting SoC Pex[1]  7 ...
	[BlueDBG] reseting SoC Pex[1]  8 ...
	[BlueDBG] reseting SoC Pex[1]  9 ...
	[BlueDBG] reseting SoC Pex[1]  10 ...
PEX1 interface detected no Link.
pci 0000:00:01.0: PME# supported from D0 D3hot
pci 0000:00:01.0: PME# disabled
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
NET: Registered protocol family 1
cpufreq: Init kirkwood cpufreq driver
XOR registered 4 channels
XOR 2nd invalidate WA enabled
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Warning: TS unit is powered off.
gpio_dev = fd00000
LED_SET_CTL_IOC_NUM= 6702
High gpio polarity = 50 
High gpio polarity = 70 
Enable Interrupt
mv88f6281_wdt: Watchdog Timer timeout = 8 sec.
mv88f6281_wdt: HW Watchdog timeout    = 15 sec.
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.12)
SGI XFS with security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 989
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
Wake up disk0......
Wake up disk1......
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access              WD800JD-00JNC0   05.0 PQ: 0 ANSI: 5
EnablePowerSaving 
PowerSavingTime = 15
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
sd 0:0:0:0: [sda] 0-byte physical blocks
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Write Protect is off
Loading Marvell Ethernet Driver:
  o Cached descriptors in DRAM
  o DRAM SW cache-coherency
  o 1 Giga ports supported
  o Single RX Queue support - ETH_DEF_RXQ=0
  o Single TX Queue support - ETH_DEF_TXQ=0
  o TCP segmentation offload (TSO) supported
  o Large Receive offload (LRO) supported
  o Receive checksum offload supported
  o Transmit checksum offload supported
  o Network Fast Processing (Routing) supported - (Disabled)
  o Driver ERROR statistics enabled
  o Proc tool API enabled
  o SKB Reuse supported - (Disabled)
  o SKB Recycle supported - (Disabled)
  o Rx descripors: q0=128
  o Tx descripors: q0=532
  o Loading network interface(s):
     o register under mv88fx_eth platform
     o eth0, ifindex = 2, GbE port = 0

mvFpRuleDb (d1110000): 16384 entries, 65536 bytes
Counter=0, opIdx=6, overhead=16
Counter=1, opIdx=2, overhead=0
Counter=2, opIdx=1, overhead=18
Counter=3, opIdx=2, overhead=0
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 3 at 0x000000060000
Bad eraseblock 134 at 0x0000010c0000
Bad eraseblock 500 at 0x000003e80000
Bad eraseblock 505 at 0x000003f20000
Bad eraseblock 563 at 0x000004660000
9 cmdlinepart partitions found on MTD device nand_mtd
Using command line partition definition
Creating 9 MTD partitions on "nand_mtd":
0x000000000000-0x000000100000 : "uboot"
0x000000100000-0x000000180000 : "uboot_env"
 sda:
0x000000180000-0x000000200000 : "key_store"
0x000000200000-0x000000280000 : "info"
 sda1 sda2
0x000000280000-0x000000c80000 : "etc"
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
0x000000c80000-0x000001680000 : "kernel_1"
0x000001680000-0x000004640000 : "rootfs1"
0x000004640000-0x000005040000 : "kernel_2"
sd 0:0:0:0: [sda] Attached SCSI disk
0x000005040000-0x000008000000 : "rootfs2"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
PCI: enabling device 0000:00:01.0 (0140 -> 0142)
xhci_hcd 0000:00:01.0: xHCI Host Controller
xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
xhci_hcd 0000:00:01.0: irq 9, io mem 0xe0000000
usb usb2: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
rtc-pcf8563 0-0051: chip found, driver version 0.4.3
rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-pcf8563 0-0051: setting system clock to 2012-09-08 13:05:56 UTC (1347109556)
Freeing init memory: 3164K
*** Stage 1: Setup system and device drivers ***
usb 1-1: new high speed USB device using ehci_marvell and address 2
In hub_port_init, and number is 1, retry 0, port 1 .....
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
eth0: mac address changed
egiga0: started
ADDRCONF(NETDEV_UP): egiga0: link is not ready
*** Stage 2: Prepare the root file system ***
Mount system partition...
yaffs: dev is 32505864 name is "mtdblock8" ro
yaffs: passed flags ""
/bin/storage_gen_mntfw.sh: line 117: e2fsck: not found
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
 sda: sda1 sda2
Filesystem label=
OS type: Linux
Block size=1024 (log=0)
Fragment size=1024 (log=0)
128520 inodes, 514048 blocks
0 blocks (0%) reserved for the super user
First data block=1
Maximum filesystem blocks=524288
63 block groups
8192 blocks per group, 8192 fragments per group
2040 inodes per group
Superblock backups stored on blocks:
	8193, 24577, 40961, 57345, 73729, 204801, 221185, 401409
/dev/sda1 /zyxel/mnt/sysdisk ext2 ro,relatime,errors=continue 0 0
0
Boot from disk
System disk image does NOT exist on HDD! Extract new firmware from NAND flash ...
sd 0:0:0:0: [sda] Sector size 0 reported, assuming 512.
 sda: sda1 sda2
Filesystem label=
OS type: Linux
Block size=1024 (log=0)
Fragment size=1024 (log=0)
128520 inodes, 514048 blocks
0 blocks (0%) reserved for the super user
First data block=1
Maximum filesystem blocks=524288
63 block groups
8192 blocks per group, 8192 fragments per group
2040 inodes per group
Superblock backups stored on blocks:
	8193, 24577, 40961, 57345, 73729, 204801, 221185, 401409
/dev/sda1 /zyxel/mnt/sysdisk ext2 rw,relatime,errors=continue 0 0
Checksum of sysdisk.img : d4d9331a04627ea6cd75b14aa8bd4266
Checksum from INFO  : d4d9331a04627ea6cd75b14aa8bd4266
Checksum pass!
Mount system disk image ...
yaffs: dev is 32505860 name is "mtdblock4" rw
yaffs: passed flags ""
/etc/zyxel/conf exist..
Start rcS2 of ZyXEL style
Set the phy back to auto-negotiation mode
base address = 40151000
words[0] = phypoke
words[1] = 1
words[2] = 4
words[3] = 1e1
:GbitPhy[0x00000001:0x00000004] <= 0x000001e1
base address = 40151000
words[0] = phypoke
words[1] = 1
words[2] = 9
words[3] = 300
:GbitPhy[0x00000001:0x00000009] <= 0x00000300
base address = 40151000
words[0] = phypoke
words[1] = 1
words[2] =NTFS driver 2.1.29 [Flags: R/O MODULE].
 0
words[3] = 9140
:GbitPhy[0x00000001:0x00000000] <= 0x00009140
*** Stage 3: Start services on HDD ***
tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' taints kernel.
Disabling lock debugging due to kernel taint
Tuxera NTFS driver 3011.12.23 [Flags: R/W MODULE].
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
PPP Deflate Compression module registered
NET: Registered protocol family 24
PPP BSD Compression module registered
modprobe: module fuse not found in modules.dep
sda
checking sda
Trying to mount /dev/sda1
mount: /dev/sda1 already mounted or /mnt/parnerkey busy
mount: according to mtab, /dev/sda1 is mounted on /zyxel/mnt/sysdisk
Fail to mount /dev/sda1
Press ENTER to continue...
Starting zylogd...
 zylog starts.
Starting uamd...
Starting ZySH daemon and client...
Start NSA-220 system daemon....
 Start ZySH daemon
zyshd: version 2.0.0 (build: 12:04:19 Jul 26 2012)
% zylog init start 
cat: can't open '/var/run/syslog-ng.pid': No such file or directory
Try to KILL SIGHUP to syslog-ng: pid=0
syslog-ng not running, start /usr/sbin/syslog-ng
Sep  8 13:06:49 (none) syslog-ng[1401]: syslog-ng starting up; version='2.0.10'
zyio_open_config success. (/etc/__system_default.xml, 0)
zyio_open_config success. (/etc/zyxel/conf/__system_default_device_ha.xml, 0)
/usr/sbin/zic -d /etc /var/zyxel/myzone_rule
/bin/ln -s -f /etc/MyZone /etc/localtime
/bin/hostname NSA325
Usage: umount [-hV]
       umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
       umount [-f] [-r] [-n] [-v] special | node...
Usage: umount [-hV]
       umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
       umount [-f] [-r] [-n] [-v] special | node...
BusyBox v1.17.2 (2012-07-26 11:58:25 CST) multi-call binary.

Usage: rmdir [OPTIONS] DIRECTORY...

Init SMB DB access... 
rm: can't remove '/var/log/samba/smb.db': No such file or directory
zyio_container_create_template(/etc/__system_default.xml): scope:[network/wlan] list:[wlan_list] type:[wlan_t] is not existed
Assemble volume....
[1444] server write-only FIFO is opened (fd=6)
[1444] server read-only FIFO is opened (fd=7)
[1444] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 277
md: md0 stopped.
md: bind<sda2>
md0: detected capacity change from 0 to 79497265152
 md0: unknown partition table
cat: can't open '/tmp/mduuid.map': No such file or directory
EXT4-fs (md0): barriers disabled
kjournald2 starting: pid 1573, dev md0:8, commit interval 5 seconds
EXT4-fs (md0): warning: maximal mount count reached, running e2fsck is recommended
EXT4-fs (md0): internal journal on md0:8
EXT4-fs (md0): delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs (md0): mounted filesystem with writeback data mode
/dev/md0 [/i-data/3a22b091]: user quotas turned on
 Startup config
POLLHUP on 7
  pid = 1444
[1444] is disconnected
[1597] server write-only FIFO is opened (fd=6)
[1597] server read-only FIFO is opened (fd=7)
[1597] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 14
argc = 1,  func = 17
argc = 1,  func = 665
argc = 2,  func = 104
argid[1]: 1077; argv[1]: ge1
argc = 5,  func = 107
argid[1]: 1077; argv[1]: ge1
argid[2]: 313; argv[2]: ip
argid[3]: 434; argv[3]: address
argid[4]: 538; argv[4]: dhcp
argc = 3,  func = 105
argid[1]: 1077; argv[1]: ge1
argid[2]: 350; argv[2]: exit
argc = 2,  func = 440
argid[1]: 1070; argv[1]: 172.20.172.254
argc = 4,  func = 442
argid[1]: 875; argv[1]: fetch
argid[2]: 628; argv[2]: auto
argid[3]: 1077; argv[3]: ge1
/bin/rm -f /var/zyxel/zysh/egiga0.metric
/bin/ip route del default via 0.0.0.0 dev egiga0
RTNETLINK answers: No such process
[1608] server write-only FIFO is opened (fd=9)
[1608] server read-only FIFO is opened (fd=10)
[1608] server error read-only FIFO is opened (fd=11)
argc = 7,  func = 77
argid[1]: 267; argv[1]: mail
argid[2]: 1396; argv[2]: 1
argid[3]: 435; argv[3]: category
argid[4]: 375; argv[4]: all
argid[5]: 461; argv[5]: level
argid[6]: 478; argv[6]: alert
mail server '1' log_category(all) is:alert 
argc = 1,  func = 441
POLLHUP on 10
  pid = 1608
[1608] is disconnected
argc = 7,  func = 77
argid[1]: 267; argv[1]: mail
argid[2]: 1396; argv[2]: 1
argid[3]: 435; argv[3]: category
argid[4]: 375; argv[4]: all
argid[5]: 461; argv[5]: level
argid[6]: 375; argv[6]: all
mail server '1' log_category(all) is:all 
argc = 2,  func = 68
argid[1]: 1069; argv[1]: time.stdtime.gov.tw
argc = 2,  func = 60
argid[1]: 1120; argv[1]: +0800
/usr/sbin/zic -d /etc /var/zyxel/myzone_rule
/bin/ln -s -f /etc/MyZone /etc/localtime
argc = 1,  func = 72
/usr/sbin/ntpdate_agent time.stdtime.gov.tw
Sep  8 21:07:00 (none) ntpdate[1648]: can't find host time.stdtime.gov.tw
Sep  8 21:07:00 (none) ntpdate[1648]: no servers can be used, exiting
argc = 4,  func = 343
argid[1]: 1213; argv[1]: ""
argid[2]: 593; argv[2]: in
argid[3]: 1214; argv[3]: "NULL"
argc = 3,  func = 50
argid[1]: 388; argv[1]: first
argid[2]: 1394; argv[2]: 1024
argc = 3,  func = 50
argid[1]: 389; argv[1]: last
argid[2]: 1394; argv[2]: 65535
argc = 1,  func = 38
killall: pure-ftpd: no process killed
Usage: umount [-hV]
       umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
       umount [-f] [-r] [-n] [-v] special | node...
Usage: umount [-hV]
       umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
       umount [-f] [-r] [-n] [-v] special | node...
BusyBox v1.17.2 (2012-07-26 11:58:25 CST) multi-call binary.

Usage: rmdir [OPTIONS] DIRECTORY...

argc = 2,  func = 192
argid[1]: 1130; argv[1]: "admin"
argc = 5,  func = 193
argid[1]: 1130; argv[1]: "admin"
argid[2]: 1407; argv[2]: 501
argid[3]: 363; argv[3]: password
argid[4]: 1153; argv[4]: D57B6DB15A934EF6DF128B2DD32BAD07:6481123D905B3BF0B74573052AF457E0
enter smb_db_update_user
argc = 5,  func = 193
argid[1]: 1130; argv[1]: "admin"
argid[2]: 1407; argv[2]: 501
argid[3]: 633; argv[3]: type
argid[4]: 634; argv[4]: admin
enter smb_db_update_user
<snip a lot of lines>
TELNET start sucDisablePowerSaving
cess!
argc = 2,TimerState = 1
  func = 146
arEnablePowerSaving 
gid[1]: 1145; arPowerSavingTime = 15
gv[1]: 15
test0
Test1
Test2
Test3:
argc = 2,  func = 149
argid[1]: 1146; argv[1]: 50
test0
Test1
Test2
Test3:
argc = 2,  func = 671
argid[1]: 1077; argv[1]: ge1
killall: httpd: no process killed
Sep  8 21:07:08 (none) httpd[1928]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache]
Sep  8 21:07:08 (none) httpd[1928]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Sep  8 21:07:08 (none) httpd[1928]: [warn] RSA server certificate CommonName (CN) `NSA325' does NOT match server name!?
Sep  8 21:07:08 (none) httpd[1928]: [error] mod_auth_zyxel: initialized.
argc = 2,  func = 160
argid[1]: 1150; argv[1]: g
exec_cmd complete
eth status = g 
ethtest0
Test1
Test2
Test3:
argc = 2,  func = 529
argid[1]: 924; argv[1]: activate
/bin/killall -USR1 app_wd
killall: app_wd: no process killed
argc = 2,  func = 18
argid[1]: 350; argv[1]: exit
argc = 1,  func = 20
POLLHUP on 7
  pid = 1597
[1597] is disconnected
configure terminal ip smb internal enable "/i-data/md0"
[1938] server write-only FIFO is opened (fd=6)
[1938] server read-only FIFO is opened (fd=7)
[1938] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 180
argid[1]: 630; argv[1]: internal
argid[2]: 302; argv[2]: enable
argid[3]: 1172; argv[3]: "/i-data/md0"
find: /var/autoshare_sata/: No such file or directory
rmdir: '/var/autoshare_sata/*': No such file or directory
ln -s "/i-data/3a22b091/Testshare" "Testshare"
ln -s "/i-data/3a22b091/admin" "admin"
ln -s "/i-data/3a22b091/encrypted" "encrypted"
ln -s "/i-data/3a22b091/music" "music"
ln -s "/i-data/3a22b091/photo" "photo"
ln -s "/i-data/3a22b091/public" "public"
ln -s "/i-data/3a22b091/test" "test"
ln -s "/i-data/3a22b091/testshare2" "testshare2"
ln -s "/i-data/3a22b091/video" "video"
EXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesRegenSmbConfigFile:2201 Close file ok
EXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesRegenSmbConfigFile:2201 Close file ok
POLLHUP on 7
  pid = 1938
[1938] is disconnected
configure terminal ip smb internal disable "/i-data/md1"
[2052] server write-only FIFO is opened (fd=6)
[2052] server read-only FIFO is opened (fd=7)
[2052] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 181
argid[1]: 630; argv[1]: internal
argid[2]: 303; argv[2]: disable
argid[3]: 1172; argv[3]: "/i-data/md1"
EXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesRegenSmbConfigFile:2201 Close file ok
no such autosata.
Error happens when deleting autosata.
POLLHUP on 7
  pid = 2052
[2052] is disconnected
configure terminal ip smb internal enable "/i-data/3a22b091"
[2062] server write-only FIFO is opened (fd=6)
[2062] server read-only FIFO is opened (fd=7)
[2062] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 180
argid[1]: 630; argv[1]: internal
argid[2]: 302; argv[2]: enable
argid[3]: 1172; argv[3]: "/i-data/3a22b091"
ln -s "/i-data/3a22b091/Testshare" "Testshare"
ln -s "/i-data/3a22b091/admin" "admin"
ln -s "/i-data/3a22b091/encrypted" "encrypted"
ln -s "/i-data/3a22b091/music" "music"
ln -s "/i-data/3a22b091/photo" "photo"
ln -s "/i-data/3a22b091/public" "public"
Sep  8 21:07:11 (none) httpd[1929]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Sep  8 21:07:11 (none) httpd[1929]: [warn] RSA server certificate CommonName (CN) `NSA325' does NOT match server name!?
Sep  8 21:07:11 (none) httpd[1929]: [error] mod_auth_zyxel: initialized.
ln -s "/i-data/3a22b091/test" "test"
ln -s "/i-data/3a22b091/testshare2" "testshare2"
ln -s "/i-data/3a22b091/video" "video"
EXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesRegenSmbConfigFile:2201 Close file ok
/var/autoshare_sata/Vol1 has pointed to other share.
EXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesEXT4: add strict allocate = yesRegenSmbConfigFile:2201 Close file ok
POLLHUP on 7
  pid = 2062
[2062] is disconnected
Starting smbd...
Starting nmbd...
Starting NSU Agent...
grep: /proc/nas_model: No such file or directory
Adding 524280k swap on /i-data/.system/swap_ul6545p.  Priority:-1 extents:4 across:542712k 
351+0 records in
351+0 records out
368050176 bytes (351.0MB) copied, 8.253989 seconds, 42.5MB/s
Setting up swapspace version 1, size = 359420 KiB
no label, UUID=63dee948-ff3d-4147-8d5d-20d9a81280ca
GMT offset=28800s
setting system time zone to tz_minuteswest=-480
mknod: /dev/btncpy: File exists
killall: dservice: no process killed
setLED COPY OFF
led_state_map_addr = 10
[2667] server write-only FIFO is opened (fd=6)
[2667] server read-only FIFO is opened (fd=7)
[2667] server error read-only FIFO is opened (fd=8)
argc = 2,  func = 348
argid[1]: 1215; argv[1]: former
Warning - readback failed
POLLHUP on 7
  pid = 2667
[2667] is disconnected
schedule_controller is already running now.
Starting "/etc/init.d/zypkg_controller.sh".
Starting to set up zy-pkgs environment ...
cp: can't stat '/etc/zyxel/zy-pkgs/*': No such file or directory
Finish "/etc/init.d/zypkg_controller.sh".
Starting "/etc/init.d/zypkg_controller.sh".
Starting all zypkgs via "/etc/init.d/zypkg_controller.sh" ...
- starting package "PHP-MySQL-phpMyAdmin" ...
---> start "PHP-MySQL-phpMyAdmin" successfully.
- starting package "gallery" ...
mkdir: can't create directory '/i-data/md0/admin/zy-pkgs/gallery': File exists
mkdir: can't create directory '/i-data/md0/admin/zy-pkgs/gallery/modules': File exists
mkdir: can't create directory '/i-data/md0/admin/zy-pkgs/gallery/themes': File exists
mkdir: can't create directory '/i-data/md0/admin/zy-pkgs/gallery/uploads': File exists
killall: mysqld: no process killed
120908 21:07:23 mysqld_safe Logging to '/usr/local/zy-pkgs/mysql/var/NSA325.err'.
120908 21:07:23 mysqld_safe Starting mysqld daemon with databases from /usr/local/zy-pkgs/mysql/var
/usr/lib/python2.6/site-packages/flickrapi/__init__.py:45: DeprecationWarning: the md5 module is deprecated; use hashlib instead
Sep  8 21:07:27 (none) zcip: init egiga0
Sep  8 21:07:27 (none) zcip: start, interface egiga0
fail to stop mysqld
---> start "gallery" successfully.
- starting package "WordPress" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/WordPress" is not existed or not excutable
- starting package "SqueezeCenter" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/SqueezeCenter" is not existed or not excutable
- starting package "eMule" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/eMule" is not existed or not excutable
- starting package "DyDNS" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/DyDNS" is not existed or not excutable
- starting package "SMART" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/SMART" is not existed or not excutable
- starting package "BackupPlanner" ...
### /i-data/.zyxel/stunnelc.log ###
### /i-data/.zyxel/stunneld.log ###
-> /i-data/.zyxel/stunneld.log exists
### /i-data/.zyxel/zysyncd.log ###
-> /i-data/.zyxel/zysyncd.log exists
### /i-data/.zyxel/zysync.log ###
### /i-data/.zyxel/BackupPlanner.log ###
-> /i-data/.zyxel/BackupPlanner.log exists
### /i-data/.system/stunnelc.log ###
### /i-data/.system/stunneld.log ###
-> /i-data/.system/stunneld.log exists
### /i-data/.system/zysyncd.log ###
-> /i-data/.system/zysyncd.log exists
### /i-data/.system/zysync.log ###
### /i-data/.system/BackupPlanner.log ###
-> /i-data/.system/BackupPlanner.log exists
Inserting cifs.ko module ...
insmod: can't insert '/usr/local/zy-pkgs/lib/cifs.ko': No such file or directory
Starting zysync server ...
===> Generate zysync server config ...
     ===> Generating volume list ...
     ===> Generating zysync config file ...
md0 : active linear sda2[0]
cat: can't open '/tmp/zysync_modules': No such file or directory
===> Starting zysync server ...
[INFO]: Starting server mode ... 

Done
Starting stunnel server ...
===> Generating stunnel server config file ...
===> Starting stunnel server ...
Sep  8 21:07:31 (none) stunnel: LOG7[3089:1073865456]: Clients allowed=500
Sep  8 21:07:31 (none) stunnel: LOG5[3089:1073865456]: stunnel 4.52 on armv5tel-unknown-linux-gnueabi platform
Sep  8 21:07:31 (none) stunnel: LOG5[3089:1073865456]: Compiled/running with OpenSSL 0.9.8o 01 Jun 2010
Sep  8 21:07:31 (none) stunnel: LOG5[3089:1073865456]: Threading:PTHREAD SSL:ENGINE Auth:none Sockets:POLL,IPv6
Sep  8 21:07:31 (none) stunnel: LOG5[3089:1073865456]: Reading configuration from file /etc/zyxel/zy-pkgs/BackupPlanner/stunnel/stunneld.conf
Sep  8 21:07:31 (none) stunnel: LOG7[3089:1073865456]: Compression not enabled
Sep  8 21:07:31 (none) stunnel: LOG7[3089:1073865456]: PRNG seeded successfully
Sep  8 21:07:31 (none) stunnel: LOG6[3089:1073865456]: Initializing SSL context for service szysync
Done
---> start "BackupPlanner" successfully.
- starting package "NFS" ...
Sep  8 21:07:31 (none) stunnel: LOG4[3089:1073865456]: Insecure file permissions on /etc/zyxel/zy-pkgs/BackupPlanner/zysync/zysync.key
Sep  8 21:07:31 (none) stunnel: LOG7[3089:1073865456]: Certificate: /etc/zyxel/zy-pkgs/BackupPlanner/zysync/zysync.cert
Sep  8 21:07:31 (none) stunnel: LOG7[3089:1073865456]: Certificate loaded
Sep  8 21:07:31 (none) stunnel: LOG7[3089:1073865456]: Key file: /etc/zyxel/zy-pkgs/BackupPlanner/zysync/zysync.key
Sep  8 21:07:31 (none) stunnel: LOG7[3089:1073865456]: Private key loaded
Sep  8 21:07:31 (none) stunnel: LOG7[3089:1073865456]: Could not load DH parameters from /etc/zyxel/zy-pkgs/BackupPlanner/zysync/zysync.cert
Sep  8 21:07:31 (none) stunnel: LOG7[3089:1073865456]: Using hardcoded DH parameters
Sep  8 21:07:31 (none) stunnel: LOG7[3089:1073865456]: DH initialized with 2048-bit key
Sep  8 21:07:31 (none) stunnel: LOG7[3089:1073865456]: ECDH initialized with curve prime256v1
Sep  8 21:07:31 (none) stunnel: LOG7[3089:1073865456]: SSL options set: 0x00000004
Sep  8 21:07:31 (none) stunnel: LOG6[3089:1073865456]: SSL context initialized
Sep  8 21:07:31 (none) stunnel: LOG5[3089:1073865456]: Configuration successful
Sep  8 21:07:31 (none) stunnel: LOG7[3089:1073865456]: Service szysync bound FD=6 to 0.0.0.0:9527
Sep  8 21:07:31 (none) stunnel: LOG7[3090:1073865456]: Created pid file /var/run/stunneld.pid
NFS:no action
---> start "NFS" successfully.
- starting package "Tftp" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/Tftp" is not existed or not excutable
- starting package "Syslog" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/Syslog" is not existed or not excutable
- starting package "pyLoad" ...
startuping pyLoad ...
DownloadDaemon is Enabled.
---> start "pyLoad" successfully.
- killing httpd ...

- starting httpd ...
Sep  8 21:07:35 (none) httpd[3298]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache]
Sep  8 21:07:35 (none) httpd[3298]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Sep  8 21:07:35 (none) httpd[3298]: [warn] RSA server certificate CommonName (CN) `NSA325' does NOT match server name!?
Sep  8 21:07:35 (none) httpd[3298]: [error] mod_auth_zyxel: initialized.
successfully.
Finish "/etc/init.d/zypkg_controller.sh".
sh: you need to specify whom to kill
Sep  8 21:07:35 (none) syslog-ng[1401]: Termination requested via signal, terminating;
Sep  8 21:07:35 (none) syslog-ng[1401]: syslog-ng shutting down; version='2.0.10'
Sep  8 21:07:35 NSA325 syslog-ng[3317]: syslog-ng starting up; version='2.0.10'
rm: can't remove '/i-data/.system/dropbox/dropbox.enable': No such file or directory
Sep  8 21:07:36 NSA325 httpd[3299]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Sep  8 21:07:36 NSA325 httpd[3299]: [warn] RSA server certificate CommonName (CN) `NSA325' does NOT match server name!?
Sep  8 21:07:36 NSA325 httpd[3299]: [error] mod_auth_zyxel: initialized.
Web Server already started.
/bin/nice: /usr/sbin/lld2d: No such file or directory
Starting app_wd...
 core_checksum : 5d1b17ef8b1c1dec7b3a76500d9b983f
 fwversion : NSA325_4.50(AAAJ.0)
 img_checksum : d4d9331a04627ea6cd75b14aa8bd4266
 modelid : AA03
 revision : 36344
 romfile_checksum : 2788
 zld_checksum : 936ed0734eccc871dff10aa1bcde782e
GbE port 0: TxEnable WA - Enabled, deep=1, tx_en_bk=1

led_state_map_addr = 46

Please press Enter to activate this console. Sep  8 21:07:38 NSA325 zcip: config egiga0 169.254.43.197
Sep  8 21:07:38 NSA325 zcip: script /usr/share/zcip.script config failed, exitcode=1

Shutdown log

Sep  8 13:08:17 NSA325 linuxrc: starting pid 3526, tty : '/etc/init.d/rc.shutdown'
led_state_map_addr = 4e
/ # Starting "/etc/init.d/zypkg_controller.sh".
Stopping all zypkgs via "/etc/init.d/zypkg_controller.sh" ...
- shutdowning package "pyLoad" ...
sh: you need to specify whom to kill
---> shutdown "pyLoad" successfully.
- shutdowning package "Syslog" ...
---> Error: shutdown program "/usr/local/zy-pkgs/etc/init.d/Syslog" is not existed or not excutable
- shutdowning package "Tftp" ...
---> Error: shutdown program "/usr/local/zy-pkgs/etc/init.d/Tftp" is not existed or not excutable
- shutdowning package "NFS" ...
Shutting down NFS: rpc.mountdkillall: rpc.mountd: no process killed
 nfsdsh: you need to specify whom to kill
 exportfs: done
---> shutdown "NFS" successfully.
- shutdowning package "BackupPlanner" ...
killing zysync
1 second
You are terminated!
killing stunnel
1 second
Sep  8 21:08:18 NSA325 stunnel: LOG7[3090:1073865456]: Dispatching signals from the signal pipe
Sep  8 21:08:18 NSA325 stunnel: LOG7[3090:1073865456]: Processing SIGNAL_TERMINATE
Sep  8 21:08:18 NSA325 stunnel: LOG5[3090:1073865456]: Terminated
Sep  8 21:08:18 NSA325 stunnel: LOG7[3090:1073865456]: Service szysync closed FD=6
Sep  8 21:08:18 NSA325 stunnel: LOG7[3090:1073865456]: str_stats: 34 block(s), 1649 data byte(s), 1156 control byte(s)
Sep  8 21:08:18 NSA325 stunnel: LOG7[3090:1073865456]: removing pid file /var/run/stunneld.pid
You are terminated!
---> shutdown "BackupPlanner" successfully.
- shutdowning package "SMART" ...
---> Error: shutdown program "/usr/local/zy-pkgs/etc/init.d/SMART" is not existed or not excutable
- shutdowning package "DyDNS" ...
---> Error: shutdown program "/usr/local/zy-pkgs/etc/init.d/DyDNS" is not existed or not excutable
- shutdowning package "SqueezeCenter" ...
---> Error: shutdown program "/usr/local/zy-pkgs/etc/init.d/SqueezeCenter" is not existed or not excutable
- shutdowning package "eMule" ...
---> Error: shutdown program "/usr/local/zy-pkgs/etc/init.d/eMule" is not existed or not excutable
- shutdowning package "gallery" ...
---> shutdown "gallery" successfully.
- shutdowning package "WordPress" ...
---> Error: shutdown program "/usr/local/zy-pkgs/etc/init.d/WordPress" is not existed or not excutable
- shutdowning package "PHP-MySQL-phpMyAdmin" ...
/usr/local/zy-pkgs/mysql/bin/mysqladmin: error while loading shared libraries: libmysqlclient.so.16: cannot open shared object file: No such file or directory
120908 21:08:19 mysqld_safe mysqld from pid file /usr/local/zy-pkgs/mysql/var/NSA325.pid ended
killall: mysqld_safe: no process killed
killall: mysqld: no process killed
---> shutdown "PHP-MySQL-phpMyAdmin" successfully.
Finish "/etc/init.d/zypkg_controller.sh".
Starting "/etc/init.d/zypkg_controller.sh".
Starting to release zy-pkgs environment ...
umount: /usr/local/zy-pkgs: device is busy.
        (In some cases useful info about processes that use
         the device is found by lsof(8) or fuser(1))
Finish "/etc/init.d/zypkg_controller.sh".
Warning - readback failed
start kill.
 1343 root      3492 S    /usr/sbin/zylogd
 1353 root      7836 S    /usr/sbin/uamd
 1621 root      5432 S <  /usr/local/sbin/dhcpcd_request egiga0 50 auto
 1700 root     13724 R N  pure-ftpd (SERVER)
 1848 root     21208 S N  /usr/bin/schedule_controller
 1849 root      1428 S N  /usr/bin/timer_source
 1862 root     30192 S N  python /usr/local/dmsf/binary/cdsdaemon.pyc
 1872 root      1684 S N  /usr/local/dmsf/binary/twonkystarter -appdata /i-dat
 1873 root     23272 S N  /usr/local/dmsf/binary/twonkyserver -appdata /i-data
 2225 root     11648 S <  /usr/sbin/nsuagent
 2504 root      2792 S N  /sbin/crond -L /dev/null
 2631 root      1564 S N  /usr/local/btn/do_btncpy
 2660 root     24256 S N  /usr/sbin/fadd
 2666 root     69872 S N  python /usr/local/fileye/fileye.pyc -f
 2885 root      2720 S <  /sbin/zcip egiga0 /usr/share/zcip.script
 3299 root     23008 S    /usr/sbin/httpd -f /etc/service_conf/httpd.conf
 3311 root      2720 S    /bin/sh -c /usr/sbin/dropbox_hook
 3312 root      2148 S    /usr/sbin/dropbox_hook
 3317 root      4288 R    syslog-ng
 3322 nobody    124m S    (wsgi:groupName -f /etc/service_conf/httpd.conf
 3323 nobody   23008 S    /usr/sbin/httpd -f /etc/service_conf/httpd.conf
 3324 nobody   23008 S    /usr/sbin/httpd -f /etc/service_conf/httpd.conf
 3364 root      2796 S    -/bin/sh
Sep  8 21:08:29 NSA325 syslog-ng[3317]: Termination requested via signal, terminating;
Sep  8 21:08:29 NSA325 syslog-ng[3317]: syslog-ng shutting down; version='2.0.10'

  3364 root      2796 S    -/bin/sh
EXT4-fs: mballoc: 3 blocks 1 reqs (0 success)
EXT4-fs: mballoc: 1 extents scanned, 0 goal hits, 1 2^N hits, 0 breaks, 0 lost
EXT4-fs: mballoc: 6 generated and it took 0
EXT4-fs: mballoc: 512 preallocated, 0 discarded
md: md0 stopped.
md: unbind<sda2>
md: export_rdev(sda2)
mdadm: stopped /dev/md0
rootfs / rootfs rw 0 0
/proc /proc proc rw,relatime 0 0
/sys /sys sysfs rw,relatime 0 0
none /proc/bus/usb usbfs rw,relatime 0 0
devpts /dev/pts devpts rw,relatime,mode=600 0 0
/dev/mtdblock8 /zyxel/mnt/nand yaffs2 ro,relatime 0 0
/dev/sda1 /zyxel/mnt/sysdisk ext2 ro,relatime,errors=continue 0 0
/dev/loop0 /ram_bin ext2 ro,relatime,errors=continue 0 0
/dev/loop0 /usr ext2 ro,relatime,errors=continue 0 0
/dev/loop0 /lib/security ext2 ro,relatime,errors=continue 0 0
/dev/loop0 /lib/modules ext2 ro,relatime,errors=continue 0 0
/dev/ram0 /tmp/tmpfs tmpfs rw,relatime,size=5120k 0 0
/dev/ram0 /usr/local/etc tmpfs rw,relatime,size=5120k 0 0
/dev/ram0 /usr/local/var tmpfs rw,relatime,size=5120k 0 0
/dev/mtdblock4 /usr/local/apache/web_framework/data/config yaffs2 rw,relatime 0 0
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system halt
md: stopping all md devices.
sd 0:0:0:0: [sda] Synchronizing SCSI cache
Power down.
reg(3, 18) = 4985
reg(0, 18) = 0
reg(17, 16) = 4500
reg(17, 25) = 6cc8
reg(17, 24) = 6f87
reg(17, 23) = f757