Dmesg (NSA-210)

Linux version 2.6.24.4 (root@Neo) (gcc version 3.4.3 (MontaVista 3.4.3-25.0.70.0501961 2005-12-18)) #1 Tue Oct 5 13:43:50 CST 2010
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
Machine: Oxsemi NAS
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 32768
  DMA zone: 256 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 32512 pages, LIFO batch:7
  Normal zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 rw init=/sbin/init initrd=0x4a000000,4M elevator=cfq mtdparts=physmap-flash.0:128k(uboot),1792k(kernel),1664k(initrd),448k(etc),48k(empty),8k(env1),8k(env2) mem=128M poweroutage=yes
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 122112KB available (3328K code, 206K data, 120K init)
Calibrating delay loop... 183.09 BogoMIPS (lpj=915456)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 64 bytes
NET: Registered protocol family 16
Number of DMA channels = 5, version = 4
Allocating 891 SRAM generic DMA descriptors
Chip Id: die-id 0x0acb1672e7c0 read back 0xbeefcafe
PCI: bus0: Fast back to back transfers enabled
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 4096K
Probing for Synopsis GMAC, unit 0
eth0: PHY is ICPlus 1001
phy init done
eth0: GMAC ver = 51, vendor ver = 17 at 0xe8000000, IRQ 8
eth0: Found PHY at address 1, type 0x02430d90 -> 10/100/1000
eth0: Ethernet addr: 00:30:e0:00:00:00
Init phy sucessfully
thermAndFan: initializing - ox810
Init led blk
Enable Interrupt
Copy button
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.9)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x44900000 (irq = 29) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ox810sata: OX810 sata core.
scsi0 : oxnassata
ata1: SATA max UDMA/133 irq 18
ata_eh_reset(2207):Sleep 1 sec before any error happens
Copy button release
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata_dev_read_id(2037): Give 100ms while getting HW ID
ata1.00: qc timeout (cmd 0xec)
ox810sata_bmdma_stop - aborting DMA
ox810sata aborting DMA.
ox810sata sending sync escapes
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata1: failed to recover some devices, retrying in 1 secs
ata_eh_reset(2207):Sleep 1 sec before any error happens
ata_wait_after_reset(3494):msleep(6000);
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata_dev_read_id(2037): Give 100ms while getting HW ID
ata1.00: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: Drive reports diagnostics failure. This may indicate a drive
ata1.00: fault or invalid emulation. Contact drive vendor for information.
ata_dev_read_id(2037): Give 100ms while getting HW ID
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HD103SI  1AG0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
ox810sata: OX810 sata core.
scsi1 : oxnassata
ata2: SATA max UDMA/133 irq 18
ata_eh_reset(2207):Sleep 1 sec before any error happens
ata2: SATA link down (SStatus 0 SControl 300)
physmap platform flash device: 00400000 at 41000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.0: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
7 cmdlinepart partitions found on MTD device physmap-flash.0
Creating 7 MTD partitions on "physmap-flash.0":
0x00000000-0x00020000 : "uboot"
mtd: Giving out device 0 to uboot
0x00020000-0x001e0000 : "kernel"
mtd: Giving out device 1 to kernel
0x001e0000-0x00380000 : "initrd"
mtd: Giving out device 2 to initrd
0x00380000-0x003f0000 : "etc"
mtd: Giving out device 3 to etc
0x003f0000-0x003fc000 : "empty"
mtd: Giving out device 4 to empty
0x003fc000-0x003fe000 : "env1"
mtd: Giving out device 5 to env1
0x003fe000-0x00400000 : "env2"
mtd: Giving out device 6 to env2
10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver@e7000000 Device ID register 42fa05
oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller
oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus number 1
oxnas-ehci oxnas-ehci.0: irq 7, io mem 0x00000000
oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
sl811: driver sl811-hcd, 19 May 2005
usb 1-1: new high speed USB device using oxnas-ehci and address 2
In hub_port_init, and number is 0, retry 0, port 1 .....
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.3: new high speed USB device using oxnas-ehci and address 3
In hub_port_init, and number is 1, retry 0, port 3 .....
usb 1-1.3: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
pcf8563 0-0051: chip found, driver version 0.4.2
pcf8563 0-0051: rtc core: registered pcf8563 as rtc0
OXNAS bit-bash I2C driver initialisation OK
md: linear personality registered for level -1
md: raid1 personality registered for level 1
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFP support v0.3: not present
drivers/rtc/hctosys.c: unable to open rtc device (rtc)
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 120K
MTD_open
MTD_read
MTD_read
MTD_close
MTD_open
MTD_read
MTD_read
MTD_close
MTD_open
MTD_read
MTD_read
MTD_close
MTD_open
MTD_read
MTD_read
MTD_close
egiga0: PHY is ICPlus 1001
Resetting GMAC
GMAC reset complete
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
egiga0: PHY is ICPlus 1001
MTD_open
MTD_read
MTD_read
MTD_close
MTD_open
MTD_read
MTD_read
MTD_close
egiga0: link down
egiga0: link up, 100Mbps, full-duplex, using pause, lpa 0x45E1
Timed out of wait for Tx to stop
scsi 2:0:0:0: Direct-Access     Sony     Storage Media    0100 PQ: 0 ANSI: 0 CCS
sd 2:0:0:0: [sdb] 7864320 512-byte hardware sectors (4027 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] 7864320 512-byte hardware sectors (4027 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00
sd 2:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1 sdb2
sd 2:0:0:0: [sdb] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
MTD_open
MTD_read
MTD_read
MTD_close
MTD_open
MTD_read
MTD_read
MTD_close
SGI XFS with large block numbers, no debug enabled
SGI XFS Quota Management subsystem
NTFS driver 2.1.29 [Flags: R/O MODULE].
tntfs: module license 'Commercial' taints kernel.
Tuxera NTFS driver 3010.6.16 [Flags: R/W MODULE].
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
MTD_open
MTD_read
MTD_read
MTD_close
MTD_open
MTD_read
MTD_read
MTD_close
md: md0 stopped.
md: bind<sda2>
Filesystem "md0": Disabling barriers, not supported by the underlying device
XFS mounting filesystem md0
Starting XFS recovery on filesystem: md0 (logdev: internal)
Ending XFS recovery on filesystem: md0 (logdev: internal)
Adding 524280k swap on /i-data/.zyxel/swap_ul6545p.  Priority:-1 extents:1 across:524280k