Category:NSA-2401

From NAS-Central Zyxel Wiki
Jump to: navigation, search
This article is currently a stub. You can help this Wiki by expanding it

. This template will categorize articles that include it into Category:Stubs.

NSA2400.jpg
NS-2401
CPU Freescale 8543 PPC @800MHz
RAM 256 MB DDR
Flash ROM 8 MB
Other
NIC Atheros AR8021
USB
internal HDD
IDE Controller
Drive Capacity
Fan


A (faulty) bootlog found here:

U-Boot 1.1.4.NSA2401 (Jan 22 2008 - 13:08:49)

CPU:   8543, Version: 2.1, (0x80320021)
Core:  e500v2, Version: 2.2, (0x80210022)
Clock Configuration:
       CPU: 799 MHz, CCB: 399 MHz,
       DDR: 199 MHz, LBC:  24 MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled

Board: MPC85xx Processor Card Rev. A.
       -- Boot Flash is U30

PEX :  X8 2.5Gbps
PCI1:  32 bit, sync
PCI2:  disabled
I2C:   ready
DRAM:  Initializing
DDR:   256 MB
FLASH:  8 MB
L2 cache 256KB: enabled
env_relocate[212] offset = 0x10050000
env_relocate[230] malloced ENV at 0ffae008
In:    serial
Out:   serial
Err:   serial
Net:   eTSEC0: PHY is Atheros AR8021 (4dd04e)
eTSEC1: PHY id ffffffff is not supported!
eTSEC2: PHY is Atheros AR8021 (4dd04e)
eTSEC3: PHY id ffffffff is not supported!
eTSEC0, eTSEC1, eTSEC2, eTSEC3
eTSEC0 & eTSEC1 in Reduce mode
eTSEC2 & eTSEC3 in Reduce mode
Hit any key to stop autoboot:  2 ��� 1 ��� 0 
## Booting image at ff800000 ...
   Image Name:   Linux-2.6.24.2
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1760657 Bytes =  1.7 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at ffa00000 ...
   Image Name:   RAM disk
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    1706142 Bytes =  1.6 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Ramdisk to 0fe0c000, end 0ffac89e ... OK
identify_ppc_sys_by_id: 0x80320021  i:13 
Memory CAM mapping: CAM0=256Mb, CAM1=0Mb, CAM2=0Mb residual: 0Mb
Linux version 2.6.24.2 (root@Neo) (gcc version 3.4.3 (MontaVista 3.4.3-25.0.70.0501961 2005-12-18)) #1 Thu Apr 12 18:31:32 CST 2012
Reg 0x404 is 0x0
Done for bus 0
Zone PFN ranges:
  DMA             0 ->    65536
  Normal      65536 ->    65536
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->    65536
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: root=/dev/ram rw mtdparts=physmap-flash.0:2048k(kernel),4544k(initrd),1024k(etc),64k(env),-(uboot) console=ttyS0,115200 init=/linuxrc
//---     init irq    ---//
OpenPIC Version 1.2 (1 CPUs and 60 IRQ sources) at fc7b9000
PID hash table entries: 1024 (order: 10, 4096 bytes)
init console call addr: 0xc037ac14
Console: colour dummy device 80x25
init console call addr: 0xc037ac18
serial8250_console_init
serial8250_isa_init_ports, UART_NR:2
serial8250_console_setup: index:0, 
serial8250_console_setup: line:0, iobase:0x0, membase:0x0
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 254336k available (2636k kernel code, 924k data, 128k init, 0k highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
net_namespace: 64 bytes
xor: measuring software checksum speed
   8regs     :   932.000 MB/sec
   8regs_prefetch:   812.000 MB/sec
   32regs    :  1004.000 MB/sec
   32regs_prefetch:   892.000 MB/sec
xor: using function: 32regs (1004.000 MB/sec)
NET: Registered protocol family 16
tty class init
PCI: Probing PCI hardware
Fixup res 2 (101) of dev 0000:00:00.0: 0 -> 803000
mpc85xx_map_irq: dev 0000:00:00.0, pin 1, idsel 0, 
mpc85xx_map_irq: dev 0001:01:00.0, pin 1, idsel 0, 
mpc85xx_map_irq: dev 0001:01:1e.0, pin 1, idsel 30, 
mpc85xx_map_irq: dev 0001:01:1e.1, pin 1, idsel 30, 
PCI: bridge rsrc 803000..1802fff (100), parent c0338954
PCI: bridge rsrc a0000000..bfffffff (200), parent c0338938
PCI: bridge rsrc 0..7fffff (100), parent c0338954
PCI: bridge rsrc 80000000..8fffffff (200), parent c0338938
PCI:0001:01:00.0: Resource 0: 0000000000000000-00000000000fffff (f=200)
PCI:  parent is c03a2058: 0000000080000000-000000008fffffff (f=200)
PCI:0001:01:00.0: Resource 1: 0000000000000000-000000007fffffff (f=1208)
PCI:  parent is c03a2058: 0000000080000000-000000008fffffff (f=200)
PCI:0001:01:00.0: Resource 2: 0000000000000000-0000000000000000 (f=204)
PCI:  parent is c03a2058: 0000000080000000-000000008fffffff (f=200)
PCI:0001:01:00.0: Resource 4: 0000000000000000-0000000000000000 (f=204)
PCI:  parent is c03a2058: 0000000080000000-000000008fffffff (f=200)
PCI:0001:01:1e.0: Resource 0: 000000008ffff000-000000008fffffff (f=200)
PCI:0001:01:1e.1: Resource 0: 000000008fffef00-000000008fffefff (f=200)
PCI:0000:00:00.0: Resource 0: 0000000014000000-00000000140fffff (f=204)
PCI:0000:00:00.0: Resource 2: 0000000000803000-00000000008030ff (f=101)
PCI: Failed to allocate mem resource #1:80000000@0 for 0001:01:00.0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 1666k freed
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
async_tx: api initialized (sync-only)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
tty init enter
tty init exit
Generic RTC Driver v1.07
Power Button : IRQ 53
Reset Button : IRQ 50
Copy Button : IRQ 54
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
Register driver, ret: 0
iobase:0x0
membase:0xfc7fa500
irq:26
uartclk:399999996
flags: 0x11000040
serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 26) is a 16550A
serial8250_console_setup: index:0, 
serial8250_console_setup: line:0, iobase:0x0, membase:0xfc7fa500
uart_set_options
console [ttyS0] enabled
ret value for serial8250_register_port:0
iobase:0x0
membase:0xfc7f9600
irq:26
uartclk:399999996
flags: 0x11000040
serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 26) is a 16550A
ret value for serial8250_register_port:1
platform_driver_register ret:0
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
loop: module loaded
Gianfar MII Bus: probed
eth0: Gianfar Ethernet Controller Version 1.2, 40:4a:03:13:d5:9e
eth0: Running with NAPI disabled
eth0: 64/64 RX/TX BD ring size
eth1: Gianfar Ethernet Controller Version 1.2, 6f:74:3d:2f:64:65
eth1: Running with NAPI disabled
eth1: 64/64 RX/TX BD ring size
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
physmap platform flash device: 00800000 at ff800000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
5 cmdlinepart partitions found on MTD device physmap-flash.0
Creating 5 MTD partitions on "physmap-flash.0":
0x00000000-0x00200000 : "kernel"
mtd: Giving out device 0 to kernel
0x00200000-0x00670000 : "initrd"
mtd: Giving out device 1 to initrd
0x00670000-0x00770000 : "etc"
mtd: Giving out device 2 to etc
0x00770000-0x00780000 : "env"
mtd: Giving out device 3 to env
0x00780000-0x00800000 : "uboot"
mtd: Giving out device 4 to uboot
ehci_hcd 0001:01:1e.1: EHCI Host Controller
ehci_hcd 0001:01:1e.1: new USB bus registered, assigned bus number 1
ehci_hcd 0001:01:1e.1: irq 48, io mem 0x8fffef00
ehci_hcd 0001:01:1e.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd 0001:01:1e.0: OHCI Host Controller
ohci_hcd 0001:01:1e.0: new USB bus registered, assigned bus number 2
ohci_hcd 0001:01:1e.0: irq 48, io mem 0x8ffff000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usb 1-3: new high speed USB device using ehci_hcd and address 2
usb 1-3: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
pcf8563 2-0051: chip found, driver version 0.4.2
pcf8563 2-0051: rtc core: registered pcf8563 as rtc0
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1    125 MB/s
raid6: int32x2    214 MB/s
raid6: int32x4    253 MB/s
raid6: int32x8    222 MB/s
raid6: using algorithm int32x4 (253 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
pcf8563 2-0051: setting system clock to 2012-10-09 08:21:22 UTC (1349770882)
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 128k init
MTD_open
MTD_read
MTD_read
MTD_close
MTD_open
MTD_read
MTD_read
MTD_close
INITRD: Trying to mount NAND flash as Root FS....scsi 0:0:0:0: Direct-Access     ZyXEL    USB DISK 2.0     PMAP PQ: 0 ANSI: 0 CCS
sd 0:0:0:0: [sda] 503808 512-byte hardware sectors (258 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 503808 512-byte hardware sectors (258 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI removable disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
.PHY: 0:01 - Link is Up - 1000/Full
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
cat: /mnt/NAND/usr/etc/Zy_Private: No such file or directory
/sbin/md5sum: /mnt/NAND/usr/etc/nsa2401_nand: No such file or directory
*kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
cat: /mnt/NAND/usr/etc/Zy_Private: No such file or directory
/sbin/md5sum: /mnt/NAND/usr/etc/nsa2401_nand: No such file or directory
*kjournald starting.  Commit interval 5 seconds

Pages in category "NSA-2401"

This category contains only the following page.