Bootlog NSA-221

From NAS-Central Zyxel Wiki
Jump to: navigation, search

Firmware 4.10(AFM.0)

1.00 U-Boot 1.1.2 (Apr 11 2010 - 20:23:49)

U-Boot code: 48D00000 -> 48D172F4  BSS: -> 48D1AFA4
RAM Configuration:
	Bank #0: 48000000 256 MB
SRAM Configuration:
	128KB at 0x58000000
Flash:  4 MB
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  2 ��� 1 ��� 0 
## Booting image at 41020000 ...
   Image Name:   Linux-2.6.24.4
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1834872 Bytes =  1.7 MB
   Load Address: 48008000
   Entry Point:  48008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux.............................................................
...................................................... done, booting the kernel.
Linux version 2.6.24.4 (root@Neo) (gcc version 3.4.3 (MontaVista 3.4.3-25.0.70.0501961 2005-12-18)) #1 Wed Sep 8 17:44:46 CST 2010
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
Machine: Oxsemi NAS
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 rw init=/sbin/init initrd=0x4a000000,4M elevator=cfq mtdparts=physmap-flash.0:128k(uboot),1792k(kernel),1664k(initrd),448k(etc),48k(empty),8k(env1),8k(env2) mem=256M poweroutage=yes
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
console [ttyS0] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 252032KB available (3336K code, 207K data, 120K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 64 bytes
NET: Registered protocol family 16
Number of DMA channels = 5, version = 4
Allocating 891 SRAM generic DMA descriptors
Chip Id: die-id 0x0b4a88762b40 read back 0xbeefcafe
PCI: bus0: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 4096K
Probing for Synopsis GMAC, unit 0
eth0: PHY is Realtek RTL8211BGR
phy init done
eth0: GMAC ver = 51, vendor ver = 17 at 0xe8000000, IRQ 8
eth0: Found PHY at address 1, type 0x001cc912 -> 10/100/1000
eth0: Ethernet addr: 00:30:e0:00:00:00
Init phy sucessfully
thermAndFan: initializing - ox810
Init led blk
Enable Interrupt
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.9)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ÿserial8250: ttyS0 at MMIO 0x44900000 (irq = 29) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ox810sata: OX810 sata core.
scsi0 : oxnassata
ata1: SATA max UDMA/133 irq 18
ata_eh_reset(2207):Sleep 1 sec before any error happens
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata_dev_read_id(2037): Give 100ms while getting HW ID
ata1.00: qc timeout (cmd 0xec)
ox810sata_bmdma_stop - aborting DMA
ox810sata aborting DMA.
ox810sata sending sync escapes
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata1: failed to recover some devices, retrying in 1 secs
ata_eh_reset(2207):Sleep 1 sec before any error happens
ata_wait_after_reset(3494):msleep(6000);
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata_dev_read_id(2037): Give 100ms while getting HW ID
ata1.00: qc timeout (cmd 0xec)
ox810sata_bmdma_stop - aborting DMA
ox810sata aborting DMA.
ox810sata sending sync escapes
ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata1: failed to recover some devices, retrying in 1 secs
ata_eh_reset(2207):Sleep 1 sec before any error happens
ata_wait_after_reset(3494):msleep(6000);
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata_dev_read_id(2037): Give 100ms while getting HW ID
ata1.00: HPA detected: current 2930277168, native 18446744072344861488
ata1.00: ATA-7: SAMSUNG HD154UI, 1AG01113, max UDMA7
ata1.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: Drive reports diagnostics failure. This may indicate a drive
ata1.00: fault or invalid emulation. Contact drive vendor for information.
ata_dev_read_id(2037): Give 100ms while getting HW ID
ata1.00: configured for UDMA/133
ata1: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x9 t4
ata_dev_read_id(2037): Give 100ms while getting HW ID
ata_dev_read_id(2037): Give 100ms while getting HW ID
ata1.00: configured for UDMA/133
ata1: EH complete
scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HD154UI  1AG0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 2930277168 512-byte hardware sectors (1500302 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 2930277168 512-byte hardware sectors (1500302 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
ox810sata: OX810 sata core.
scsi1 : oxnassata
ata2: SATA max UDMA/133 irq 18
ata_eh_reset(2207):Sleep 1 sec before any error happens
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata_dev_read_id(2037): Give 100ms while getting HW ID
ata2.00: qc timeout (cmd 0xec)
ox810sata_bmdma_stop - aborting DMA
ox810sata aborting DMA.
ox810sata sending sync escapes
ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata2: failed to recover some devices, retrying in 1 secs
ata_eh_reset(2207):Sleep 1 sec before any error happens
ata_wait_after_reset(3494):msleep(6000);
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata_dev_read_id(2037): Give 100ms while getting HW ID
ata2.00: qc timeout (cmd 0xec)
ox810sata_bmdma_stop - aborting DMA
ox810sata aborting DMA.
ox810sata sending sync escapes
ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata2: failed to recover some devices, retrying in 1 secs
ata_eh_reset(2207):Sleep 1 sec before any error happens
ata_wait_after_reset(3494):msleep(6000);
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata_dev_read_id(2037): Give 100ms while getting HW ID
ata2.00: HPA detected: current 2930277168, native 18446744072344861488
ata2.00: ATA-7: SAMSUNG HD154UI, 1AG01118, max UDMA7
ata2.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata2.00: Drive reports diagnostics failure. This may indicate a drive
ata2.00: fault or invalid emulation. Contact drive vendor for information.
ata_dev_read_id(2037): Give 100ms while getting HW ID
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access     ATA      SAMSUNG HD154UI  1AG0 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 2930277168 512-byte hardware sectors (1500302 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 2930277168 512-byte hardware sectors (1500302 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdb: sdb1 sdb2
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg1 type 0
physmap platform flash device: 00400000 at 41000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.0: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
7 cmdlinepart partitions found on MTD device physmap-flash.0
Creating 7 MTD partitions on "physmap-flash.0":
0x00000000-0x00020000 : "uboot"
mtd: Giving out device 0 to uboot
0x00020000-0x001e0000 : "kernel"
mtd: Giving out device 1 to kernel
0x001e0000-0x00380000 : "initrd"
mtd: Giving out device 2 to initrd
0x00380000-0x003f0000 : "etc"
mtd: Giving out device 3 to etc
0x003f0000-0x003fc000 : "empty"
mtd: Giving out device 4 to empty
0x003fc000-0x003fe000 : "env1"
mtd: Giving out device 5 to env1
0x003fe000-0x00400000 : "env2"
mtd: Giving out device 6 to env2
10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver@e7000000 Device ID register 42fa05
oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller
oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus number 1
oxnas-ehci oxnas-ehci.0: irq 7, io mem 0x00000000
oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
USB Universal Host Controller Interface driver v3.0
sl811: driver sl811-hcd, 19 May 2005
usb 1-1: new high speed USB device using oxnas-ehci and address 2
In hub_port_init, and number is 0, retry 0, port 1 .....
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.1: new high speed USB device using oxnas-ehci and address 3
In hub_port_init, and number is 1, retry 0, port 1 .....
usb 1-1.1: configuration #1 chosen from 1 choice
usb 1-1.2: new high speed USB device using oxnas-ehci and address 4
In hub_port_init, and number is 2, retry 0, port 2 .....
usb 1-1.2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
scsi3 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
pcf8563 0-0051: chip found, driver version 0.4.2
pcf8563 0-0051: rtc core: registered pcf8563 as rtc0
OXNAS bit-bash I2C driver initialisation OK
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFP support v0.3: not present
drivers/rtc/hctosys.c: unable to open rtc device (rtc)
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 120K
init started:  BusyBox v1.1.1 (2010.09.08-09:47+0000) multi-call binary
Starting pid 814, console /dev/ttyS0: '/etc/init.d/rcS'
MTD_open
MTD_read
MTD_read
MTD_close
MTD_open
MTD_read
MTD_read
MTD_close
Mounting file systems...
MTD_open
MTD_read
MTD_read
MTD_close
MTD_open
MTD_read
MTD_read
MTD_close
egiga0: PHY is Realtek RTL8211BGR
Resetting GMAC
GMAC reset complete
Starting udhcpc ...
INITRD: Trying to mount NAND flash as Root FS.egiga0: PHY is Realtek RTL8211BGR
egiga0: link down
..egiga0: link up, 100Mbps, full-duplex, using pause, lpa 0x45E1
Timed out of wait for Tx to stop
scsi 2:0:0:0: Direct-Access     SanDisk  Cruzer           8.02 PQ: 0 ANSI: 0 CCS
scsi 3:0:0:0: Direct-Access     ZyXEL    USB DISK 2.0     PMAP PQ: 0 ANSI: 0 CCS
sd 2:0:0:0: [sdc] 31825919 512-byte hardware sectors (16295 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Assuming drive cache: write through
sd 2:0:0:0: [sdc] 31825919 512-byte hardware sectors (16295 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Assuming drive cache: write through
 sdc: sdc1
sd 2:0:0:0: [sdc] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg2 type 0
.sd 3:0:0:0: [sdd] 247808 512-byte hardware sectors (127 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Assuming drive cache: write through
sd 3:0:0:0: [sdd] 247808 512-byte hardware sectors (127 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Assuming drive cache: write through
 sdd: sdd1
sd 3:0:0:0: [sdd] Attached SCSI removable disk
sd 3:0:0:0: Attached scsi generic sg3 type 0
/dev/sdc
mount upgrade key
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sdd1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Find compressed sys image NAND
MTD_open
MTD_read
MTD_read
MTD_close
MTD_open
MTD_read
MTD_read
MTD_close
e2fsck 1.38 (30-Jun-2005)
/dev/sda1: clean, 13/128520 files, 506600/514048 blocks
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
/dev/sda1 /zyxel/mnt/sysdisk ext3 ro,data=ordered 0 0
 Flag_HD_Exists = 0
Boot from disk
Checksum of sysdisk.img : 657aec5f89bd9bd375791c486b1d6790
Checksum from INFO  : 657aec5f89bd9bd375791c486b1d6790
Checksum Pass
killall: udhcpc: no process killed
cp: /ram_bin/home/*: No such file or directory
cp: /ram_bin/mnt/*: No such file or directory
Creating device nodes...done.
MTD_open
MTD_read
MTD_read
MTD_close
MTD_open
MTD_read
MTD_read
MTD_close
/etc/zyxel/conf exist..
SGI XFS with large block numbers, no debug enabled
SGI XFS Quota Management subsystem
NTFS driver 2.1.29 [Flags: R/O MODULE].
tntfs: module license 'Commercial' taints kernel.
Tuxera NTFS driver 3010.6.16 [Flags: R/W MODULE].
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
modprobe: could not parse modules.dep

usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
sda
sdb
sdc
sdd
checking sda
Trying to mount /dev/sda1
mount: /dev/sda1 already mounted or /mnt/parnerkey busy
mount: according to mtab, /dev/sda1 is mounted on /zyxel/mnt/sysdisk
Fail to mount /dev/sda1
checking sdb
Trying to mount /dev/sdb1
NTFS-fs warning (device sdb1): parse_options(): Option iocharset is deprecated. 
Please use option nls=<charsetname> in the future.
NTFS-fs error (device sdb1): parse_options(): Unrecognized mount option shortname.
mount: wrong fs type, bad option, bad superblock on /dev/sdb1,
       or too many mounted file systems
Fail to mount /dev/sdb1
checking sdc
Trying to mount /dev/sdc1
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
cp: `/mnt/parnerkey/usb_key_func.sh' and `/mnt/parnerkey/usb_key_func.sh' are the same file
cmd = cat /etc/Zy_Private /mnt/parnerkey/usb_key_func.sh | md5sum -c /mnt/parnerkey/salted_md5sum 
md5 check ok
MTD_open
MTD_read
MTD_read
MTD_close
MTD_open
MTD_read
MTD_read
MTD_close
checking sdd
Trying to mount /dev/sdd1
Press ENTER to continue...
Starting zylogd...
 zylog starts.
Starting uamd...
Starting ZySH daemon and client...
Start NSA-220 system daemon....
 Start ZySH daemon
zyshd: version 2.0.0 (build: 17:51:08 Sep  8 2010)
% zylog init start 
cat: /var/run/syslog-ng.pid: No such file or directory
Try to KILL SIGHUP to syslog-ng: pid=0
syslog-ng not running, start /usr/sbin/syslog-ng
zyio_open_config success. (/etc/__system_default.xml, 0)
zyio_open_config success. (/etc/zyxel/conf/__system_default_device_ha.xml, 0)
/usr/sbin/zic -d /etc /var/zyxel/myzone_rule
Oct 25 09:56:44 (none) syslog-ng[2039]: syslog-ng starting up; version='2.0.10'
/bin/ln -s -f /etc/MyZone /etc/localtime
/bin/hostname nsa221
Usage: umount [-hV]
       umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
       umount [-f] [-F] [-r] [-n] [-v] special | node...
Usage: umount [-hV]
       umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
       umount [-f] [-F] [-r] [-n] [-v] special | node...
find: /home/shares: No such file or directory
BusyBox v1.1.1 (2010.09.08-09:48+0000) multi-call binary

Usage: rmdir [OPTION]... DIRECTORY...

Init SMB DB access... 
rm: cannot remove `/var/log/samba/smb.db': No such file or directory
sd 2:0:0:0: [sdc] 31825919 512-byte hardware sectors (16295 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Assuming drive cache: write through
 sdc: sdc1 sdc2
sd 2:0:0:0: [sdc] 31825919 512-byte hardware sectors (16295 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Assuming drive cache: write through
 sdc: sdc1 sdc2
Assemble volume....
[2102] server write-only FIFO is opened (fd=6)
[2102] server read-only FIFO is opened (fd=7)
[2102] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 276
md: md0 stopped.
md: bind<sdb2>
md: bind<sda2>
raid1: raid set md0 active with 2 out of 2 mirrors
raid1 using hardware RAID 0x00000001
cat: /tmp/mduuid.map: No such file or directory
Filesystem "md0": Disabling barriers, not supported by the underlying device
XFS mounting filesystem md0
[2102] is disconnected
 Startup config
[2172] server write-only FIFO is opened (fd=6)
[2172] server read-only FIFO is opened (fd=7)
[2172] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 14
argc = 1,  func = 17
argc = 2,  func = 104
argid[1]: 1059; argv[1]: ge1
argc = 5,  func = 107
argid[1]: 1059; argv[1]: ge1
argid[2]: 313; argv[2]: ip
argid[3]: 434; argv[3]: address
argid[4]: 538; argv[4]: dhcp
argc = 4,  func = 106
argid[1]: 1059; argv[1]: ge1
argid[2]: 540; argv[2]: mtu
argid[3]: 1375; argv[3]: 9216
argc = 3,  func = 105
argid[1]: 1059; argv[1]: ge1
argid[2]: 350; argv[2]: exit
argc = 3,  func = 418
argid[1]: 1052; argv[1]: 194.25.2.129
argid[2]: 1052; argv[2]: 193.101.111.20
argc = 4,  func = 420
argid[1]: 857; argv[1]: fetch
argid[2]: 858; argv[2]: manually
argid[3]: 1059; argv[3]: ge1
/bin/rm -f /var/zyxel/zysh/egiga0.metric
/bin/ip route del default via 0.0.0.0 dev egiga0
ip: RTNETLINK answers: No such process
Oct 25 09:56:54 (none) dhcpcd[2203]: dhcpT1value is 129600 sec
Oct 25 09:56:54 (none) dhcpcd[2203]: dhcpT2value is 226800 sec
Oct 25 09:56:54 (none) dhcpcd[2203]: dhcpT1value is 129600 sec
Oct 25 09:56:54 (none) dhcpcd[2203]: dhcpT2value is 226800 sec
argc = 2,  func = 68
argid[1]: 1051; argv[1]: time.stdtime.gov.tw
[2226] server write-only FIFO is opened (fd=9)
[2226] server read-only FIFO is opened (fd=10)
[2226] server error read-only FIFO is opened (fd=11)
argc = 2,  func = 60
argid[1]: 1102; argv[1]: +0100
/usr/sbin/zic -d /etc /var/zyxel/myzone_rule
/bin/ln -s -f /etc/MyZone /etc/localtime
argc = 1,  func = 422
POLLHUP on 10
  pid = 2226
[2226] is disconnected
argc = 1,  func = 72
/usr/sbin/ntpdate_agent time.stdtime.gov.tw
argc = 4,  func = 340
argid[1]: 1195; argv[1]: "CET"
argid[2]: 592; argv[2]: in
argid[3]: 1196; argv[3]: "Amsterdam,Berlin,Bern,Rome,Stockholm,Vienna"
argc = 2,  func = 57
argid[1]: 1094; argv[1]: nsa221-kk2
smb_share.c: editing_config lack of smb_global settings
cat: /var/run/nmbd.pid: No such file or directory
BusyBox v1.1.1 (2010.09.08-09:48+0000) multi-call binary

Usage: kill [-signal] process-id [process-id ...]

killall: crond: no process killed
killall: timer_source: no process killed
killall: schedule_controller: no process killed
/bin/hostname nsa221-kk2
RegenSmbConfigFile:2114 Close file ok
===> Stopping crond ...
===> Starting crond ...
===> Stopping schedule_controller ...
argc = 3,  func = 199
argid[1]: 1157; argv[1]: zyxeltech
argid[2]: 649; argv[2]: nomaster
smb_share.c: editing_config lack of smb_global settings
killall: timer_source: no process killed
smb_share.c: editing_config lack of smb_global settings
RegenSmbConfigFile:2114 Close file ok
===> Starting schedule_controller ...
RegenSmbConfigFile:2114 Close file ok
argc = 3,  func = 40
argid[1]: 286; argv[1]: port
argid[2]: 1360; argv[2]: 21
argc = 1,  func = 38
killall: pure-ftpd: no process killed
Usage: umount [-hV]
       umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
       umount [-f] [-F] [-r] [-n] [-v] special | node...
Usage: umount [-hV]
       umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
       umount [-f] [-F] [-r] [-n] [-v] special | node...
BusyBox v1.1.1 (2010.09.08-09:48+0000) multi-call binary

Usage: rmdir [OPTION]... DIRECTORY...

argc = 2,  func = 192
argid[1]: 1112; argv[1]: "admin"
argc = 5,  func = 193
argid[1]: 1112; argv[1]: "admin"
argid[2]: 1379; argv[2]: 501
argid[3]: 363; argv[3]: password
argid[4]: 1135; argv[4]: <SKIPPED>
43AC94C233
enter smb_db_update_user
argc = 5,  func = 193
argid[1]: 1112; argv[1]: "admin"
argid[2]: 1379; argv[2]: 501
argid[3]: 632; argv[3]: type
argid[4]: 633; argv[4]: admin
enter smb_db_update_user
argc = 4,  func = 189
argid[1]: 1112; argv[1]: "admin"
argid[2]: 1379; argv[2]: 501
argid[3]: 350; argv[3]: exit
argc = 2,  func = 192

<SKIPPED SOME MORE SAMBA SHARE LOGS>

/bin/rm /etc/service_conf/httpd_zld.conf
/bin/mv /etc/service_conf/httpd_zld.conf.new /etc/service_conf/httpd_zld.conf
/bin/killall -HUP httpd
killall: httpd: no process killed
argc = 2,  func = 146
argid[1]: 1127; argv[1]: 3
test0
Test1
Test2
Test3:
argc = 2,  func = 149
argid[1]: 1128; argv[1]: 50
test0
Test1
Test2
Test3:
argc = 2,  func = 503
argid[1]: 905; argv[1]: activate
/bin/killall -USR1 app_wd
killall: app_wd: no process killed
argc = 2,  func = 18
argid[1]: 350; argv[1]: exit
argc = 1,  func = 20
POLLHUP on 7
  pid = 2172
[2172] is disconnected
configure terminal ip smb internal enable "/i-data/md0"
[2505] server write-only FIFO is opened (fd=6)
[2505] server read-only FIFO is opened (fd=7)
[2505] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 180
argid[1]: 629; argv[1]: internal
argid[2]: 302; argv[2]: enable
argid[3]: 1154; argv[3]: "/i-data/md0"
smb_share.c: editing_config lack of smb_global settings
RegenSmbConfigFile:2114 Close file ok
Starting smbd...
POLLHUP on 7
  pid = 2505
[2505] is disconnected
Starting nmbd...
Starting NSU Agent...
readlink: /i-data/md1: No such file or directory
configure terminal ip smb internal disable "/i-data/md1"
[2525] server write-only FIFO is opened (fd=6)
[2525] server read-only FIFO is opened (fd=7)
[2525] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 181
argid[1]: 629; argv[1]: internal
argid[2]: 303; argv[2]: disable
argid[3]: 1154; argv[3]: "/i-data/md1"
smb_share.c: editing_config lack of smb_global settings
RegenSmbConfigFile:2114 Close file ok
POLLHUP on 7
  pid = 2525
[2525] is disconnected
configure terminal ip smb internal enable "/i-data/f899eb57"
[2555] server write-only FIFO is opened (fd=6)
[2555] server read-only FIFO is opened (fd=7)
[2555] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 180
argid[1]: 629; argv[1]: internal
argid[2]: 302; argv[2]: enable
argid[3]: 1154; argv[3]: "/i-data/f899eb57"
smb_share.c: editing_config lack of smb_global settings
RegenSmbConfigFile:2114 Close file ok
POLLHUP on 7
  pid = 2555
[2555] is disconnected
cat: /etc/zyxel/zyfw/ac_status: No such file or directory
Setting up swapspace version 1, size = 526381 kB
Adding 514040k swap on /dev/sdb1.  Priority:-1 extents:1 across:514040k
Adding 524280k swap on /i-data/.zyxel/swap_ul6545p.  Priority:-2 extents:2 across:732768924k
storage_gen_swap.sh:/zyxel/mnt/sysdisk/swap_ul6545p exists
GMT offset=7200s
setting system time zone to tz_minuteswest=-120
/sbin/adjtimex: invalid option -- -
BusyBox v1.1.1 (2010.09.08-09:48+0000) multi-call binary

Usage: adjtimex [-q] [-o offset] [-f frequency] [-p timeconstant] [-t tick]

mknod: /dev/btncpy: File exists
Starting diagnosed...
[2826] server write-only FIFO is opened (fd=6)
[2826] server read-only FIFO is opened (fd=7)
[2826] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 19
POLLHUP on 7
  pid = 2826
[2826] is disconnected
setLED COPY OFF
led_state_map_addr = 10
Starting app_wd...
[2923] server write-only FIFO is opened (fd=6)
[2923] server read-only FIFO is opened (fd=7)
[2923] server error read-only FIFO is opened (fd=8)
argc = 2,  func = 345
argid[1]: 1197; argv[1]: former
POLLHUP on 7
  pid = 2923
[2923] is disconnected
schedule_controller is already running now.
Starting "/etc/init.d/zypkg_controller.sh".
Starting to set up zy-pkgs environment ...
[2944] server write-only FIFO is opened (fd=6)
[2944] server read-only FIFO is opened (fd=7)
[2944] server error read-only FIFO is opened (fd=8)
argc = 2,  func = 304
argid[1]: 1167; argv[1]: /dev/sdc1
cp: /etc/zyxel/zy-pkgs/*: No such file or directory
Finish "/etc/init.d/zypkg_controller.sh".
Starting "/etc/init.d/zypkg_controller.sh".
Starting all zypkgs via "/etc/init.d/zypkg_controller.sh" ...
- starting package "PHP-MySQL-phpMyAdmin" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/PHP-MySQL-phpMyAdmin" is not existed or not excutable
- starting package "gallery" ...
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/gallery" is not existed or not excutable
- starting package "WordPress" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/WordPress" is not existed or not excutable
- starting package "SqueezeCenter" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/SqueezeCenter" is not existed or not excutable
- starting package "eMule" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/eMule" is not existed or not excutable
- starting package "DyDNS" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/DyDNS" is not existed or not excutable
- starting package "SMART" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/SMART" is not existed or not excutable
- starting package "BackupPlanner" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/BackupPlanner" is not existed or not excutable
- starting package "NFS" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/NFS" is not existed or not excutable
- starting package "Tftp" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/Tftp" is not existed or not excutable
- starting package "Syslog" ...
---> Error: start-up program "/usr/local/zy-pkgs/etc/init.d/Syslog" is not existed or not excutable
/etc/init.d/zypkg_controller.sh: /etc/init.d/zypkg_controller.sh: 491: cannot open /i-data/md0/admin/zy-pkgs/USRPKG_DEPS_START: No such file
Finish "/etc/init.d/zypkg_controller.sh".
smb_share.c: editing_config lack of smb_global settings
No BackupPlanner package inside this firmware.
POLLHUP on 7
  pid = 2944
[2944] is disconnected
[3320] server write-only FIFO is opened (fd=6)
[3320] server read-only FIFO is opened (fd=7)
[3320] server error read-only FIFO is opened (fd=8)
argc = 2,  func = 398
argid[1]: 1217; argv[1]: /dev/sdc1
POLLHUP on 7
  pid = 3320
[3320] is disconnected
[3335] server write-only FIFO is opened (fd=6)
[3335] server read-only FIFO is opened (fd=7)
[3335] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 19
POLLHUP on 7
  pid = 3335
[3335] is disconnected
setLED COPY GREEN ON
led_state_map_addr = 16
Starting Web Server...
Oct 25 11:57:38 (none) httpd[3376]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache]
Oct 25 11:57:38 (none) httpd[3376]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Oct 25 11:57:38 (none) httpd[3376]: [warn] RSA server certificate CommonName (CN) `nsa221-kk2' does NOT match server name!?
Oct 25 11:57:38 (none) httpd[3376]: [error] mod_auth_zyxel: initialized.
led_state_map_addr = 46
 core_checksum : EAD6
 fwversion : V4.10(AFM.0)
 image_checksum : 657aec5f89bd9bd375791c486b1d6790 sysdisk.img
 img_checksum : 43528a70348be68a6dc8812b9909b1ad sysdisk.img
 initrd_checksum : 92E2
 modelid : DC01
 revision : 24376
 romfile_checksum : 01FA
 zld_checksum : 6E4D

Please press Enter to activate this console. Oct 25 11:57:40 (none) httpd[3387]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Oct 25 11:57:40 (none) httpd[3387]: [warn] RSA server certificate CommonName (CN) `nsa221-kk2' does NOT match server name!?
Oct 25 11:57:40 (none) httpd[3387]: [error] mod_auth_zyxel: initialized.

*********************************************
*		HD:sdb standby now	    *
*********************************************
*********************************************
*		HD:sda standby now	    *
*********************************************
*********************************************
*		HD:sda standby now	    *
*********************************************