Bootlog (NAS540)

From NAS-Central Zyxel Wiki
Jump to: navigation, search
uloader 2011.06.0 (May 20 2014 - 16:36:41)

Board: Mindspeed C2000
c2k_spi_probe

Copying Barebox from SPI Flash(bootopt=0)
BB Copying Done
## Starting Barebox at 0x01000000 ...

barebox 2011.06.0-svn44305-dirty6 (Aug 28 2014 - 22:25:22)

Board: Mindspeed C2000
c2k_spi_probe
c2k_otp_probe.
cbus_baseaddr: 9c000000, ddr_baseaddr: 03800000, ddr_phys_baseaddr: 03800000
class init complete
tmu init complete
bmu1 init: done
bmu2 init: done
util init complete
GPI1 init complete
GPI2 init complete
HGPI init complete
HIF rx desc: base_va: 03e80000, base_pa: 03e80000
HIF tx desc: base_va: 03e80400, base_pa: 03e80400
HIF init complete
bmu1 enabled
bmu2 enabled
pfe_hw_init: done
pfe_firmware_init
pfe_load_elf
pfe_load_elf no of sections: 10
pfe_firmware_init: class firmware loaded
pfe_load_elf
pfe_load_elf no of sections: 10
pfe_firmware_init: tmu firmware loaded
pfe_load_elf
pfe_load_elf no of sections: 14
pfe_firmware_init: util firmware loaded
eth_port: 0
NAS540_phy_reg_setting[eth_port].phyaddr: 0x4
miidev_restart_aneg for PHY4
eth_port: 1
NAS540_phy_reg_setting[eth_port].phyaddr: 0x6
miidev_restart_aneg for PHY6
cfi_probe: cfi_flash base: 0xc0000000 size: 0x04000000
## Unknown FLASH on Bank at 0xc0000000 - Size = 0x00000000 = 0 MB
bootopt = 0x0
Using ENV from SPI Flash.
nand_probe: comcerto_nand base: 0xc8300000 size: 0x256 MB
NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD NAND 256MiB 3,3V 8-bit), page size: 2048, OOB size: 64
Using default values 
Bad block table not found for chip 0
Bad block table not found for chip 0
Scanning device for bad blocks
Bad block table written to 0x0ffe0000, version 0x01
Bad block table written to 0x0ffc0000, version 0x01
Malloc space: 0x00600000 -> 0x01000000 (size 10 MB)
Stack space : 0x005f8000 -> 0x00600000 (size 32 kB)
running /env/bin/init...
Unknown command 'export' - try 'help'

Hit any key to stop autoboot:  3## 2## 1## 0

booting kernel of type uimage from /dev/nand0.kernel1.bb
   Verifying Checksum ... OK
   Image Name:   Linux-3.2.54
   Created:      2014-10-20  12:24:54 UTC
   Image Type:   <NULL> <NULL> <NULL> (<NULL>)
   Data Size:    8418952 Bytes =  8 MB
   Load Address: 0f008000
   Entry Point:  0f008000
OK

Starting kernel ...

commandline: console=ttyS0,115200n8, init=/etc/preinit pcie_gen1_only=yes  mac_addr=,, ip=dhcp root=ubi0:rootfs ubi.mtd=2,2048 rootfstype=ubifs rw noinitrd mtdparts=spi0.0:256k(uloader)ro,512k(barebox)ro,256k(env);comcertonand:10M(config),10M(kernel1),110M(rootfs1),10M(kernel2),110M(rootfs2),-(reserved) usb3_internal_clk=yes

arch_number: 1094

Uncompressing Linux... done, booting the kernel.
#[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Linux version 3.2.54 (root@BuildMachine) (collect2: ld returned 1 exit status) #2 SMP Mon Oct 20 20:24:49 CST 2014
[    0.000000] CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=50c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: Comcerto 2000 EVM
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Comcerto: zone_dma mapping size=2c00000 type=b
[    0.000000] PERCPU: Embedded 2 pages/cpu @84c20000 s71232 r8192 d51648 u131072
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16055
[    0.000000] Kernel command line: console=ttyS0,115200n8, init=/etc/preinit pcie_gen1_only=yes  mac_addr=,, ip=dhcp root=ubi0:rootfs ubi.mtd=2,2048 rootfstype=ubifs rw noinitrd mtdparts=spi0.0:256k(uloader)ro,512k(barebox)ro,256k(env);comcertonand:10M(config),10M(kernel1),110M(rootfs1),10M(kernel2),110M(rootfs2),-(reserved) usb3_internal_clk=yes
[    0.000000] PID hash table entries: 4096 (order: -2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 3, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 2, 262144 bytes)
[    0.000000] Memory: 44MB 960MB = 1004MB total
[    0.000000] Memory: 1014272k/1014272k available, 34304k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0x00000000   (  64 kB)
[    0.000000]     fixmap  : 0xfff30000 - 0xfffe0000   ( 704 kB)
[    0.000000]     vmalloc : 0xc0800000 - 0xf0000000   ( 760 MB)
[    0.000000]     lowmem  : 0x80000000 - 0xc0000000   (1024 MB)
[    0.000000]     modules : 0x83600000 - 0x84000000   (  10 MB)
[    0.000000]       .text : 0x84008000 - 0x84587128   (5629 kB)
[    0.000000]       .init : 0x84590000 - 0x84a71640   (4998 kB)
[    0.000000]       .data : 0x84a80000 - 0x84ad4070   ( 337 kB)
[    0.000000]        .bss : 0x84ad4094 - 0x84b64808   ( 578 kB)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:256
[    0.000000] PLL0 running at 2400 MHz, PLL1 at 1000 MHz PLL2 running at 1500 MHz PLL3 running at 1066 MHz
[    0.000000] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 17179ms
[    0.000186] Calibrating delay loop... 2387.14 BogoMIPS (lpj=11935744)
[    0.060028] pid_max: default: 32768 minimum: 301
[    0.060260] Mount-cache hash table entries: 8192
[    0.061381] Initializing cgroup subsys cpuacct
[    0.061410] Initializing cgroup subsys devices
[    0.061450] CPU: Testing write buffer coherency: ok
[    0.061712] CPU0: thread -1, cpu 0, socket 9, mpidr 80000900
[    0.061738] Calibrating local timer... 299.82MHz.
[    0.120070] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.121062] CPU1 powered up
[    0.121659] CPU1: Booted secondary processor
[    0.180031] CPU1: thread -1, cpu 1, socket 9, mpidr 80000901
[    0.180084] Brought up 2 CPUs
[    0.180095] SMP: Total of 2 processors activated (4780.85 BogoMIPS).
[    0.181741] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 2
[    0.190282] xor: measuring software checksum speed
[    0.240157]    arm4regs  :   140.800 MB/sec
[    0.290111]    8regs     :   147.200 MB/sec
[    0.339960]    32regs    :    89.600 MB/sec
[    0.390023]    neon      :   147.200 MB/sec
[    0.390031] xor: using function: neon (147.200 MB/sec)
[    0.390382] NET: Registered protocol family 16
[    0.392055] L310 cache controller enabled
[    0.392067] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x00c40000, PREFETCH_CTRL 0x00000000, Cache size: 262144 B
[    0.392145] ARMv7 AUX CTRL(0): 0x41
[    0.392150] ARMv7 AUX CTRL(0): 0x41
[    0.392165] ARMv7 AUX CTRL(1): 0x41
[    0.392173] ARMv7 AUX CTRL(1): 0x41
[    0.393011] Pin Select for GPIO[15:0]: 05000000
[    0.393018] Pin Select for GPIO[31:16]: 00555540
[    0.393023] Output Enable for GPIO[31:0]: DFFFFF00
[    0.393028] Pin Select for GPIO[59:32]: 0FFFFFFE
[    0.393033] Pin Select for GPIO[63:60]: 00000020
[    0.393038] Output Enable for GPIO[63:32]: 00000001
[    0.393043] #[033mEnable USB ...#[0m
[    0.394195] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.394203] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.394218] Power Management Mode Support For C2000: 
[    0.394555] PCIe: Ref clk 48Mhz
[    0.394562] PCIe: Detected C2K RevA1 device serdes clk devider old:new=2e:6
[    0.397325] PCIe0: Link Up Success 
[    0.397331] PCIe0: Polarity: 0 Gen1 mode: 1 External Clk: 0
[    0.397336] comcerto_pcie_rc_int_init
[    0.397851] PCI: bus0: Fast back to back transfers disabled
[    0.398018] pci 0000:00:00.0: BAR 6: assigned [mem 0xa0000000-0xa000ffff pref]
[    0.398028] pci 0000:00:00.0: BAR 5: assigned [mem 0xa0010000-0xa00101ff]
[    0.398040] pci 0000:00:00.0: BAR 5: set to [mem 0xa0010000-0xa00101ff] (PCI address [0xa0010000-0xa00101ff])
[    0.422806] bio: create slab <bio-0> at 0
[    0.589826] raid6: int32x1    122 MB/s
[    0.759846] raid6: int32x2    105 MB/s
[    0.929960] raid6: int32x4    106 MB/s
[    1.100013] raid6: int32x8    105 MB/s
[    1.269543] raid6: neonx1     176 MB/s
[    1.439518] raid6: neonx2     185 MB/s
[    1.609403] raid6: neonx4     174 MB/s
[    1.779363] raid6: neonx8     162 MB/s
[    1.779369] raid6: using algorithm neonx2 (185 MB/s)
[    1.779651] vgaarb: loaded
[    1.780155] SCSI subsystem initialized
[    1.780993] usbcore: registered new interface driver usbfs
[    1.781213] usbcore: registered new interface driver hub
[    1.781357] usbcore: registered new device driver usb
[    1.782323] Switching to clocksource timer2
[    1.792313] NET: Registered protocol family 2
[    1.792567] IP route cache hash table entries: 16384 (order: 0, 65536 bytes)
[    1.793212] TCP established hash table entries: 32768 (order: 2, 262144 bytes)
[    1.793552] TCP bind hash table entries: 32768 (order: 2, 262144 bytes)
[    1.793859] TCP: Hash tables configured (established 32768 bind 32768)
[    1.793866] TCP reno registered
[    1.793875] UDP hash table entries: 2048 (order: 0, 65536 bytes)
[    1.794052] UDP-Lite hash table entries: 2048 (order: 0, 65536 bytes)
[    1.794510] NET: Registered protocol family 1
[    1.794792] RPC: Registered named UNIX socket transport module.
[    1.794799] RPC: Registered udp transport module.
[    1.794804] RPC: Registered tcp transport module.
[    1.794809] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    2.153467] gpio_dev = fd00000
[    2.153835] membuf_init: created membuf device(252, 0)
[    2.153907] clock_frequency_set: (1:24) NTG INCR value is 422212465
[    2.208631] VFS: Disk quotas dquot_6.5.2
[    2.208808] Dquot-cache hash table entries: 16384 (order 0, 65536 bytes)
[    2.209727] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    2.210150] JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    2.210310] fuse init (API version 7.17)
[    2.217356] Btrfs loaded
[    2.217391] msgmni has been set to 1980
[    2.223025] async_tx: api initialized (async)
[    2.225140] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    2.225155] io scheduler noop registered (default)
[    2.225289] io scheduler cfq registered
[    2.237372] ### comcerto_dma_probe: XOR DMA channel registered
[    2.246893] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    2.403228] 84b51594 84aa1828 0 ffffffff
[    2.404292] serial8250 serial8250.0: Couldn't set LCR to 191
[    2.405994] serial8250 serial8250.0: Couldn't set LCR to 191
[    2.407467] serial8250 serial8250.0: Couldn't set LCR to 224
[    2.409555] serial8250 serial8250.0: Couldn't set LCR to 224
[    2.429590] serial8250.0: ttyS0 at MMIO 0x96400000 (irq = 59) is a 16550A
[    3.130259] console [ttyS0] enabled
[    3.173079] comcerto_otp_probe.
[    3.262134] loop: module loaded
[    3.288165] PCI: enabling device 0000:00:00.0 (0140 -> 0142)
[    3.293970] ahci: SSS flag set, parallel bus scan disabled
[    3.299513] ahci 0000:00:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[    3.307645] ahci 0000:00:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs 
[    3.348485] scsi0 : ahci
[    3.362422] scsi1 : ahci
[    3.369360] ata1: SATA max UDMA/133 abar m512@0xa0010000 port 0xa0010100 irq 96
[    3.376733] ata2: SATA max UDMA/133 abar m512@0xa0010000 port 0xa0010180 irq 96
[    3.393037] SATA Serdes: 48Mhz ref clk
[    3.397281] Serdes1: Lane OK Passed
[    3.401248] Serdes2: Lane OK Passed
[    3.404787] ahci ahci: forcing PORTS_IMPL to 0x3
[    3.409470] ahci ahci: AHCI 0001.0300 32 slots 2 ports 3 Gbps 0x3 impl platform mode
[    3.417266] ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc apst 
[    3.457644] scsi2 : ahci_platform
[    3.470992] scsi3 : ahci_platform
[    3.478628] ata3: SATA max UDMA/133 mmio [mem 0x9d000000-0x9d00ffff] port 0x100 irq 48
[    3.486611] ata4: SATA max UDMA/133 mmio [mem 0x9d000000-0x9d00ffff] port 0x180 irq 48
[    3.496821] designware_spi_probe:Initializing SPI Controller : Using dma=0 CLK(DUS)=250000000 Hz
[    3.513880] comcerto_spi comcerto_spi.1: at 0x96500000 mapped to 0xC0980000, irq=60
[    3.521626] designware_spi_probe:Initializing SPI Controller : Using dma=0 CLK(spi_i2c)=250000000 Hz
[    3.551028] comcerto_spi comcerto_spi.0: at 0x90498000 mapped to 0xC09A8000, irq=61
[    3.584639] comcertoflash: probe of comcertoflash.0 failed with error -5
[    3.593789] m25p80 spi0.0: found mx25l8005, expected s25fl256s0
[    3.599735] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[    3.604594] 3 cmdlinepart partitions found on MTD device spi0.0
[    3.610530] Creating 3 MTD partitions on "spi0.0":
[    3.615355] 0x000000000000-0x000000040000 : "uloader"
[    3.640578] 0x000000040000-0x0000000c0000 : "barebox"
[    3.667760] 0x0000000c0000-0x000000100000 : "env"
[    3.689473] pdev->resource->start = c8300000, pdev->resource->end = c8301fff
[    3.696666] nand_probe: comcertonand base: 0xc0800000 
[    3.701849] ONFI flash detected
[    3.705097] ONFI param page 0 valid
[    3.708599] NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD S34ML02G1)
[    3.715769] hw_syndrome correction 2048.
[    3.719701] Using default values for hw ecc
[    3.727166] Bad block table not found for chip 0
[    3.732407] ata1: SATA link down (SStatus 0 SControl 320)
[    3.735048] Bad block table not found for chip 0
[    3.735053] Scanning device for bad blocks
[    3.812624] Bad block table written to 0x00000ffe0000, version 0x01
[    3.820742] Bad block table written to 0x00000ffc0000, version 0x01
[    3.827048] 6 cmdlinepart partitions found on MTD device comcertonand
[    3.833514] Creating 6 MTD partitions on "comcertonand":
[    3.838844] 0x000000000000-0x000000a00000 : "config"
[    3.852586] ata4: SATA link down (SStatus 0 SControl 320)
[    3.858035] ata3: SATA link down (SStatus 0 SControl 320)
[    3.864991] 0x000000a00000-0x000001400000 : "kernel1"
[    3.883882] 0x000001400000-0x000008200000 : "rootfs1"
[    3.911019] 0x000008200000-0x000008c00000 : "kernel2"
[    3.929970] 0x000008c00000-0x00000fa00000 : "rootfs2"
[    3.954358] 0x00000fa00000-0x000010000000 : "reserved"
[    3.999604] Fixed MDIO Bus: probed
[    4.005065] ## xhci_plat_probe
[    4.008139] ### comcerto_start_xhci
[    4.011646] USB3.0 clock selected: internal
[    4.018939] xhci-hcd xhci-hcd: xHCI Host Controller
[    4.023990] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
[    4.031746] xhci-hcd xhci-hcd: irq 54, io mem 0x9f000000
[    4.037156] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    4.043985] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.051227] usb usb1: Product: xHCI Host Controller
[    4.056132] usb usb1: Manufacturer: Linux 3.2.54 xhci-hcd
[    4.061544] usb usb1: SerialNumber: xhci-hcd
[    4.069235] hub 1-0:1.0: USB hub found
[    4.073079] hub 1-0:1.0: 1 port detected
[    4.082575] ata2: SATA link down (SStatus 0 SControl 320)
[    4.085380] xhci-hcd xhci-hcd: xHCI Host Controller
[    4.085408] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
[    4.085478] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[    4.085484] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.085490] usb usb2: Product: xHCI Host Controller
[    4.085494] usb usb2: Manufacturer: Linux 3.2.54 xhci-hcd
[    4.085499] usb usb2: SerialNumber: xhci-hcd
[    4.100807] hub 2-0:1.0: USB hub found
[    4.100826] hub 2-0:1.0: 1 port detected
[    4.136011] usbcore: registered new interface driver usblp
[    4.136018] Initializing USB Mass Storage driver...
[    4.154532] usbcore: registered new interface driver usb-storage
[    4.160588] USB Mass Storage support registered.
[    4.165248] dwc_otg: version 2.94a 27-OCT-2011
hotplug390add:
hotplug391add:[9/0/0]USB hub device:09h/xxh/xxh
hotplug393add:
hotplug394add:9
hotplug394add:[9/0/0]USB hub device:09h/xxh/xxh
[    4.369918] Core Release: 2.81a
[    4.369926] Setting default values for core params
[    4.569938] Using Buffer DMA mode
[    4.573295] Periodic Transfer Interrupt Enhancement - disabled
[    4.579142] Multiprocessor Interrupt Enhancement - disabled
[    4.582369] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[    4.591292] OTG VER PARAM: 0, OTG VER FLAG: 0
[    4.595811] dwc_otg dwc_otg.0: DWC OTG Controller
[    4.600570] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 3
[    4.607670] dwc_otg dwc_otg.0: irq 53, io mem 0x00000000
[    4.613070] Init: Port Power? op_state=1
[    4.617037] Init: Power Port (0)
[    4.620327] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    4.627155] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.634425] usb usb3: Product: DWC OTG Controller
[    4.639177] usb usb3: Manufacturer: Linux 3.2.54 dwc_otg
[    4.644522] usb usb3: SerialNumber: dwc_otg.0
[    4.650159] usb 1-1: New USB device found, idVendor=174c, idProduct=2074
[    4.656946] usb 1-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[    4.664168] usb 1-1: Product: ASM107x
[    4.667868] usb 1-1: Manufacturer: Asmedia
[    4.672000] usb 1-1: SerialNumber: 0000000A0003
[    4.672282] hub 3-0:1.0: USB hub found
[    4.672300] hub 3-0:1.0: 1 port detected
hotplug399add:
[    4.714225] hub 1-1:1.0: USB hub found
[    4.718329] hub 1-1:1.0: 4 ports detected
[    4.744672] mousedev: PS/2 mouse device common for all mice
hotplug400add:9
hotplug401add:
[    4.816146] c2k-rtc c2k-rtc: rtc core: registered c2k as rtc0
[    4.821916] C2000 RTC, (c) 2012 Mindspeed Technologies
hotplug400add:[9[    4.827240] c2k-rtc c2k-rtc: Warning: Invalid RTC value so initializing it
/0/0]USB hub device:09h/xxh/xxh
hotplug403add:9
[    4.849830] i2c /dev entries driver
hotplug403add:[9/0/1]USB hub dev[    4.863739] comcerto_i2c_calculate_dividers: speed=97kHz, M=1, N=7, dividers=0x0f
ice:09h/xxh/xxh
[    4.897858] i2c-core: driver [eeprom] using legacy suspend method
[    4.904008] i2c-core: driver [eeprom] using legacy resume method
[    4.911504] comcerto_wdt: support registered
[    4.912587] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[    4.924684] md: linear personality registered for level -1
[    4.930210] md: raid0 personality registered for level 0
[    4.935570] md: raid1 personality registered for level 1
[    4.940895] md: raid10 personality registered for level 10
[    4.946416] md: raid6 personality registered for level 6
[    4.951753] md: raid5 personality registered for level 5
[    4.957103] md: raid4 personality registered for level 4
[    4.962759] usb 2-1: New USB device found, idVendor=174c, idProduct=3074
[    4.969488] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[    4.972385] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[    4.985137] usb 2-1: Product: ASM107x
[    4.988852] usb 2-1: Manufacturer: Asmedia
[    4.992978] usb 2-1: SerialNumber: 0000000A0003
[    5.027014] hub 2-1:1.0: USB hub found
[    5.031156] hub 2-1:1.0: 4 ports detected
hotplug426add:
hotplug429add:9
[    5.112993] usbcore: registered new interface driver usbhid
[    5.118584] usbhid: USB HID core driver
[    5.123224] etherip: Ethernet over IPv4 tunneling driver
[    5.128583] etherip  ----- is functionalhotplug429add:[9/0/0]USB hub device:09h/xxh/xxh
[    5.147887] TCP cubic registered

[    5.152799] NET: Registered protocol family 10
[    5.159892] IPv6 over IPv4 tunneling driver
[    5.205699] NET: Registered protocol family 17
[    5.210292] 8021q: 802.1Q VLAN Support v1.8
[    5.214547] Clocks: disabled unused uart
[    5.218481] Clocks: disabled unused gemtx
[    5.222521] Clocks: disabled unused ipsec_spacc
[    5.227063] Clocks: disabled unused dpi_cie
[    5.231256] Clocks: disabled unused dpi_decomp
[    5.235728] Clocks: disabled unused pcie1
[    5.239748] Clocks: disabled unused ext_phy0
[    5.244042] Clocks: disabled unused ext_phy1
[    5.248321] Clocks: disabled unused ext_phy2
[    5.252616] Clocks: disabled unused tpi
[    5.256462] Clocks: disabled unused csys
[    5.260393] Clocks: disabled unused tsuntg
[    5.264512] Clocks: disabled unused sata_occ
[    5.268793] Clocks: disabled unused pcie_occ
[    5.273088] Clocks: disabled unused sgmii_occ
[    5.297630] UBI: attaching mtd2 to ubi0
[    5.305455] UBI: scanning is finished
[    5.309130] UBI error: ubi_read_volume_table: the layout volume was not found
[    5.316306] UBI error: ubi_attach_mtd_dev: failed to attach mtd2, error -22
[    5.323304] UBI error: ubi_init: cannot attach mtd2
[    5.328289] c2k-rtc c2k-rtc: setting system clock to 2012-07-12 18:25:01 UTC (1342117501)
[    5.336494] Registering CPUFreq(comcerto)
[    5.351748] Freeing init memory: 4992K
#[031m*** Stage 1: Setup system and device drivers ***#[0m
led_state_map_addr = 4a
hotplug486add:
hotplug488add:
hotplug490add:
hotplug487add:9
hotplug489add:9
hotplug487add:[9/0/0]USB hub device:09h/xxh/xxh
hotplug489add:[9/0/0]USB hub device:09h/xxh/xxh
hotplug492add:
hotplug491add:9
hotplug494add:
hotplug491add:[9/0/0]USB hub device:09h/xxh/xxh
hotplug495add:9
hotplug493add:9
hotplug495add:[9/0/0]USB hub device:09h/xxh/xxh
hotplug493add:[9/0/2]USB hub device:09h/xxh/xxh
[    8.324720] pfe_module_init
[    8.327583] pfe_platform_probe
[    8.331550] ipsec: baseaddr :9a000000 --- c0c00000
[    8.337416] pfe_probe
[    8.339698] PFE Driver version:
[    8.339701] pfe_ctrl_12_00_2
[    8.339703] built with pfe sources version: pfe_12_00_2
[    8.350992] cbus_baseaddr: c3000000, ddr_baseaddr: c2000000, ddr_phys_baseaddr: 3400000, ddr_size: c00000
[    8.360632] pfe_hw_init
[    8.363129] CLASS version: 20
[    8.366106] TMU version: 1011231
[    8.369345] BMU1 version: 21
[    8.372236] BMU2 version: 21
[    8.375141] EMAC1 network cfg: 80000
[    8.378730] EMAC2 network cfg: 80000
[    8.382317] EMAC3 network cfg: 80000
[    8.385963] EGPI1 version: 50
[    8.388971] EGPI2 version: 50
[    8.391969] EGPI3 version: 50
[    8.394990] HGPI version: 50
[    8.397879] GPT version: 0
[    8.400595] HIF version: 10
[    8.403412] HIF NOPCY version: 10
[    8.406737] UTIL version: 20
[    8.409629] bmu_init(1) done
[    8.412532] bmu_init(2) done
[    8.427798] class_init() done
[    8.430781] tmu_init: mem init
[    8.433860] tmu_init: lmem init
[    8.437067] tmu_init() done
[    8.439872] util_init() done
[    8.442780] gpi_init(1) done
[    8.445673] gpi_init(2) done
[    8.448725] gpi_init(3) done
[    8.451652] gpi_init(hif) done
[    8.454820] bmu_enable(1) done
[    8.457919] bmu_enable(2) done
[    8.461009] pfe_hif_lib_init
[    8.464009] pfe_hif_init
[    8.466551] pfe_hif_alloc_descr
[    8.470004] pfe_hif_init_buffers
[    8.474094] pfe_firmware_init
[    8.898814] pfe_load_elf
[    8.901366] pe_load_ddr_section: load address(3fb0000) and elf file address(c0bca000) rcvd
[    8.931835] PFE binary version: pfe_12_00_2
[    8.936045] pfe_firmware_init: class firmware loaded 0xb20 0xc3010000
[    8.942507] pfe_load_elf
[    8.946369] pfe_firmware_init: tmu firmware loaded 0x220
[    8.951694] pfe_load_elf
[    8.956041] pfe_firmware_init: util firmware loaded 0x16c0
[    8.961564] pfe_ctrl_init
[    8.982451] pfe_ctrl_init finished
[    8.982456] pfe_ctrl_timer
[    8.988576] pfe_eth_init
[    9.014183] Comcerto MDIO Bus: probed
[    9.185944] eth0: pfe_eth_init_one: created interface, baseaddr: c3200000
[    9.375961] eth1: pfe_eth_init_one: created interface, baseaddr: c3220000
[    9.382810] pfe_vwd_init
[    9.385516] pfe_vwd_init: created vwd device(250, 0)
[    9.390491] pfe_vwd_driver_init: start
[    9.394271] pfe_vwd_up: start
[    9.397279] comcerto_wifi_rx_fastpath_register:33 VWD Tx function registered
[    9.404366] pfe_vwd_driver_init: end
[    9.407951] pfe_pcap_init
ls: /dev/comcerto_wdt: No such file or directory
-rw-r--r--    1 root     root             0 Jul 12 18:25 /proc/mcu_wdt
[   11.464583]  #[033mMCU watchdog is reset!#[0m
BusyBox v1.19.4 (2014-10-20 19:21:55 CST) multi-call binary.

Usage: ifconfig [-a] interface [address]

BusyBox v1.19.4 (2014-10-20 19:21:55 CST) multi-call binary.

Usage: ifconfig [-a] interface [address]

[   12.011107] egiga0: pfe_eth_open
[   12.014567] hif_process_client_req: register client_id 0
[   12.019893] pfe_hif_client_register
[   12.023415] hif_lib_set_rx_cpu_affinity:Client (0) and HIF Rx processing will use same cpu
[   12.031711] egiga0: pfe_gemac_init
[   12.052948] egiga1: pfe_eth_open
[   12.056368] hif_process_client_req: register client_id 1
[   12.061694] pfe_hif_client_register
[   12.065238] hif_lib_set_rx_cpu_affinity:Client (1) and HIF Rx processing will use same cpu
[   12.073544] egiga1: pfe_gemac_init
#[031m*** Stage 2: Prepare the root file system ***#[0m
mknod: /dev/gpio: File exists
Initialize fan control
Wrote to  0x90470058: 0x05000000
Wrote to  0x90458000: 0x80000001
Wrote to  0x90458028: 0x80001388
#[033mMount system partition...#[0m
ls: /dev/ubi*: No such file or directory
#[033mCreating /dev/ubi_ctrl ...#[0m

[   12.835768] UBI: attaching mtd5 to ubi5
[   13.564273] UBI: scanning is finished
[   13.587997] UBI: attached mtd5 (name "rootfs1", size 110 MiB) to ubi5
[   13.594474] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[   13.601281] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[   13.608011] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[   13.614909] UBI: good PEBs: 880, bad PEBs: 0, corrupted PEBs: 0
[   13.620845] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[   13.628004] UBI: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 2004936479
[   13.637079] UBI: available PEBs: 10, total reserved PEBs: 870, PEBs reserved for bad PEB handling: 40
[   13.646336] UBI: background thread "ubi_bgt5d" started, PID 1122
UBI device number 5, total 880 LEBs (111738880 bytes, 106.6 MiB), available 10 LEBs (1269760 bytes, 1.2 MiB), LEB size 126976 bytes (124.0 KiB)
[   13.794037] UBIFS: mounted UBI device 5, volume 0, name "ubi_rootfs1"
[   13.800498] UBIFS: mounted read-only
[   13.804093] UBIFS: file system size:   103612416 bytes (101184 KiB, 98 MiB, 816 LEBs)
[   13.811944] UBIFS: journal size:       5206016 bytes (5084 KiB, 4 MiB, 41 LEBs)
[   13.819278] UBIFS: media format:       w4/r0 (latest is w4/r0)
[   13.825131] UBIFS: default compressor: lzo
[   13.829237] UBIFS: reserved for root:  4893869 bytes (4779 KiB)
ls: /sys/block/sd?: No such file or directory
/bin/storage_asm_mntfw_swap.sh: line 349: can't open /tmp/intern_disk.list: no such file
can not found fw raid uuid
can not found swap raid uuid
/bin/storage_asm_mntfw_swap.sh: line 359: can't open /tmp/intern_disk.list: no such file
storage_asm_mntfw_swap.sh can not swap on /dev/md1
1
WARNING: No valid partition on HDD or no HDD plugged!
WARNING: No valid partition on HDD or no HDD plugged
Boot from RAM disk
[   16.072561] PHY: comcerto-0:06 - Link is Up - 100/Full
[   16.077741] pfe_eth_adjust_link: PHY: comcerto-0:06, phy->link: 1
/sbin/egiga_link_up.sh ...
#[031mNo zysh daemon exists, do nothing.#[0m
#[033mMount system disk image ...#[0m
[   34.472576] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   34.483468] EXT4-fs (loop0): mounted filesystem without journal. Opts: (null)
mount: mount point /usr/local/var does not exist
[   34.709898] UBI: attaching mtd3 to ubi3
[   34.779848] UBI: scanning is finished
[   34.802861] UBI: attached mtd3 (name "config", size 10 MiB) to ubi3
[   34.809175] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[   34.815993] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[   34.822718] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[   34.829611] UBI: good PEBs: 80, bad PEBs: 0, corrupted PEBs: 0
[   34.835465] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[   34.842624] UBI: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 2787559679
[   34.851693] UBI: available PEBs: 0, total reserved PEBs: 80, PEBs reserved for bad PEB handling: 40
[   34.860793] UBI: background thread "ubi_bgt3d" started, PID 1228
UBI device number 3, total 80 LEBs (10158080 bytes, 9.7 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[   34.957307] UBIFS: recovery needed
[   35.124380] UBIFS: recovery completed
[   35.128057] UBIFS: mounted UBI device 3, volume 0, name "ubi_config"
[   35.134444] UBIFS: file system size:   3428352 bytes (3348 KiB, 3 MiB, 27 LEBs)
[   35.141774] UBIFS: journal size:       1015809 bytes (992 KiB, 0 MiB, 6 LEBs)
[   35.148936] UBIFS: media format:       w4/r0 (latest is w4/r0)
[   35.154788] UBIFS: default compressor: lzo
[   35.158895] UBIFS: reserved for root:  161928 bytes (158 KiB)
mount /etc/zyxel successfully and /etc/zyxel/conf exist, nothing special.
Start rcS2 of ZyXEL style
#[031m*** Stage 3: Start services on HDD ***#[0m
[   35.411053] NTFS driver 2.1.30 [Flags: R/O MODULE].
[   35.432513] tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' taints kernel.
[   35.442110] Disabling lock debugging due to kernel taint
[   35.456292] Tuxera NTFS driver 3014.4.29 [Flags: R/W MODULE].
[   35.490655] PPP generic driver version 2.4.2
[   35.530405] PPP MPPE Compression module registered
[   35.572953] PPP Deflate Compression module registered
[   35.587004] NET: Registered protocol family 24
[   35.619114] PPP BSD Compression module registered

Press ENTER to continue...
Starting zylogd...
 zylog starts.
Starting uamd...
Starting ZySH daemon and client...
Start NAS540 system daemon....
 Start ZySH daemon
zyshd: version 2.0.0 (build: 19:40:14 Oct 20 2014)
% zylog init start 
cat: can't open '/var/run/syslog-ng.pid': No such file or directory
Try to KILL SIGHUP to syslog-ng: pid=0
syslog-ng not running, start /usr/sbin/syslog-ng
Oct 22 09:34:39 (none) syslog-ng[1478]: syslog-ng starting up; version='2.0.10'
zyio_open_config success. (/etc/__system_default.xml, 0)
zyio_open_config success. (/etc/zyxel/conf/__system_default_device_ha.xml, 0)
/usr/sbin/zic -d /etc /var/zyxel/myzone_rule
/bin/ln -s -f /etc/MyZone /etc/localtime
/bin/hostname NAS540

Usage:
 umount [-hV]
 umount -a [options]
 umount [options] <source> | <directory>

Options:
 -a, --all               unmount all filesystems
 -A, --all-targets       unmount all mountpoints for the given device in the
                           current namespace
 -c, --no-canonicalize   don't canonicalize paths
 -d, --detach-loop       if mounted loop device, also free this loop device
     --fake              dry run; skip the umount(2) syscall
 -f, --force             force unmount (in case of an unreachable NFS system)
 -i, --internal-only     don't call the umount.<type> helpers
 -n, --no-mtab           don't write to /etc/mtab
 -l, --lazy              detach the filesystem now, clean up things later
 -O, --test-opts <list>  limit the set of filesystems (use with -a)
 -R, --recursive         recursively unmount a target with all its children
 -r, --read-only         in case unmounting fails, try to remount read-only
 -t, --types <list>      limit the set of filesystem types
 -v, --verbose           say what is being done

 -h, --help     display this help and exit
 -V, --version  output version information and exit

For more details see umount(8).

Usage:
 umount [-hV]
 umount -a [options]
 umount [options] <source> | <directory>

Options:
 -a, --all               unmount all filesystems
 -A, --all-targets       unmount all mountpoints for the given device in the
                           current namespace
 -c, --no-canonicalize   don't canonicalize paths
 -d, --detach-loop       if mounted loop device, also free this loop device
     --fake              dry run; skip the umount(2) syscall
 -f, --force             force unmount (in case of an unreachable NFS system)
 -i, --internal-only     don't call the umount.<type> helpers
 -n, --no-mtab           don't write to /etc/mtab
 -l, --lazy              detach the filesystem now, clean up things later
 -O, --test-opts <list>  limit the set of filesystems (use with -a)
 -R, --recursive         recursively unmount a target with all its children
 -r, --read-only         in case unmounting fails, try to remount read-only
 -t, --types <list>      limit the set of filesystem types
 -v, --verbose           say what is being done

 -h, --help     display this help and exit
 -V, --version  output version information and exit

For more details see umount(8).
find: /home/shares: No such file or directory
BusyBox v1.19.4 (2014-10-20 19:21:55 CST) multi-call binary.

Usage: rmdir [OPTIONS] DIRECTORY...

Init SMB DB access... 
rm: can't remove '/var/log/samba/smb.db': No such file or directory
WARNING: can't open config file: /usr/ssl/openssl.cnf
 Startup config
[1531] server write-only FIFO is opened (fd=6)
[1531] server read-only FIFO is opened (fd=7)
[1531] server error read-only FIFO is opened (fd=8)
argc = 2,  func = 679
argid[1]: 1392; argv[1]: create
/bin/touch /tmp/iface_lock_file
[1531] is disconnected
[1537] server write-only FIFO is opened (fd=6)
[1537] server read-only FIFO is opened (fd=7)
[1537] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 14
argc = 1,  func = 17
argc = 2,  func = 104
argid[1]: 1088; argv[1]: ge1
argc = 7,  func = 106
argid[1]: 1088; argv[1]: ge1
argid[2]: 313; argv[2]: ip
argid[3]: 434; argv[3]: address
argid[4]: 538; argv[4]: dhcp
argid[5]: 540; argv[5]: metric
argid[6]: 1420; argv[6]: 7
killall: httpd: no process killed
Oct 22 09:34:45 (none) httpd[1547]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache]
Oct 22 09:34:45 (none) httpd[1547]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Oct 22 09:34:45 (none) httpd[1547]: [warn] RSA server certificate CommonName (CN) `NAS540' does NOT match server name!?
Oct 22 09:34:45 (none) httpd[1547]: [error] mod_auth_zyxel: initialized.
argc = 4,  func = 107
argid[1]: 1088; argv[1]: ge1
argid[2]: 541; argv[2]: mtu
argid[3]: 1421; argv[3]: 1500
argc = 3,  func = 105
argid[1]: 1088; argv[1]: ge1
argid[2]: 350; argv[2]: exit
Oct 22 09:34:45 (none) httpd[1552]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Oct 22 09:34:45 (none) httpd[1552]: [warn] RSA server certificate CommonName (CN) `NAS540' does NOT match server name!?
Oct 22 09:34:45 (none) httpd[1552]: [error] mod_auth_zyxel: initialized.
/sbin/egiga_link_down.sh ...
argc = 2,  func = 104
argid[1]: 1088; argv[1]: ge2
argc = 7,  func = 106
argid[1]: 1088; argv[1]: ge2
argid[2]: 313; argv[2]: ip
argid[3]: 434; argv[3]: address
argid[4]: 538; argv[4]: dhcp
argid[5]: 540; argv[5]: metric
argid[6]: 1420; argv[6]: 5
Oct 22 09:34:48 (none) httpd[1596]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache]
Oct 22 09:34:48 (none) httpd[1596]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Oct 22 09:34:48 (none) httpd[1596]: [warn] RSA server certificate CommonName (CN) `NAS540' does NOT match server name!?
Oct 22 09:34:48 (none) httpd[1596]: [error] mod_auth_zyxel: initialized.
argc = 4,  func = 107
argid[1]: 1088; argv[1]: ge2
argid[2]: 541; argv[2]: mtu
argid[3]: 1421; argv[3]: 1500
argc = 3,  func = 105
argid[1]: 1088; argv[1]: ge2
argid[2]: 350; argv[2]: exit
Oct 22 09:34:49 (none) httpd[1601]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Oct 22 09:34:49 (none) httpd[1601]: [warn] RSA server certificate CommonName (CN) `NAS540' does NOT match server name!?
Oct 22 09:34:49 (none) httpd[1601]: [error] mod_auth_zyxel: initialized.
argc = 2,  func = 104
argid[1]: 1088; argv[1]: bond0
argc = 2,  func = 434
argid[1]: 1081; argv[1]: 192.168.111.1
argc = 3,  func = 436
argid[1]: 882; argv[1]: fetch
argid[2]: 639; argv[2]: auto
/bin/rm -f /var/zyxel/zysh/egiga0.metric
/bin/ip route del default via 0.0.0.0 dev egiga0
RTNETLINK answers: No such process
/bin/rm -f /var/zyxel/zysh/egiga1.metric
/bin/ip route del default via 0.0.0.0 dev egiga1
Oct 22 09:34:59 (none) dhcpcd[1656]: dhcpT1value is 129600 sec
Oct 22 09:34:59 (none) dhcpcd[1656]: dhcpT2value is 226800 sec
Oct 22 09:34:59 (none) dhcpcd[1656]: dhcpT1value is 129600 sec
Oct 22 09:34:59 (none) dhcpcd[1656]: dhcpT2value is 226800 sec
/bin/rm -f /var/zyxel/zysh/bond0.metric
argc = 7,  func = 77
argid[1]: 267; argv[1]: mail
argid[2]: 1413; argv[2]: 1
argid[3]: 435; argv[3]: category
argid[4]: 375; argv[4]: all
argid[5]: 461; argv[5]: level
argid[6]: 478; argv[6]: alert
mail server '1' log_category(all) is:alert 
argc = 7,  func = 77
argid[1]: 267; argv[1]: mail
argid[2]: 1413; argv[2]: 1
argid[3]: 435; argv[3]: category
argid[4]: 375; argv[4]: all
argid[5]: 461; argv[5]: level
argid[6]: 375; argv[6]: all
mail server '1' log_category(all) is:all 
argc = 2,  func = 68
argid[1]: 1080; argv[1]: pool.ntp.org
argc = 2,  func = 60
argid[1]: 1131; argv[1]: +0100
/usr/sbin/zic -d /etc /var/zyxel/myzone_rule
/bin/ln -s -f /etc/MyZone /etc/localtime
argc = 12,  func = 65
argid[1]: 406; argv[1]: begin
argid[2]: 409; argv[2]: mar
argid[3]: 389; argv[3]: last
argid[4]: 425; argv[4]: sun
argid[5]: 1132; argv[5]: 02:00
argid[6]: 349; argv[6]: end
argid[7]: 416; argv[7]: oct
argid[8]: 389; argv[8]: last
argid[9]: 425; argv[9]: sun
argid[10]: 1132; argv[10]: 03:00
argid[11]: 1133; argv[11]: 1
argc = 1,  func = 63
/usr/sbin/zic -d /etc /var/zyxel/myzone_rule
/bin/ln -s -f /etc/MyZone /etc/localtime
argc = 1,  func = 72
/usr/sbin/ntpdate_agent pool.ntp.org
argc = 4,  func = 334
argid[1]: 1222; argv[1]: ""
argid[2]: 599; argv[2]: in
argid[3]: 1223; argv[3]: "Amsterdam,Berlin,Bern,Rome,Stockholm,Vienna"
argc = 3,  func = 203
argid[1]: 1187; argv[1]: WORKGROUP
argid[2]: 661; argv[2]: nomaster
share path /i-data/sysvol/video not existing.
share path /i-data/sysvol/photo not existing.
share path /i-data/sysvol/music not existing.
share path /i-data/sysvol/admin not existing.
cat: can't open '/var/run/nmbd.pid': No such file or directory
kill: you need to specify whom to kill
Oct 22 11:36:28 (none) ntpdate[1707]: step time server 212.18.3.18 offset 83.547260 sec
share path /i-data/sysvol/video not existing.
share path /i-data/sysvol/photo not existing.
share path /i-data/sysvol/music not existing.
share path /i-data/sysvol/admin not existing.
RegenSmbConfigFile:2125 Close file ok
RegenSmbConfigFile:2125 Close file ok
argc = 1,  func = 38
killall: pure-ftpd: no process killed

Usage:
 umount [-hV]
 umount -a [options]
 umount [options] <source> | <directory>

Options:
 -a, --all               unmount all filesystems
 -A, --all-targets       unmount all mountpoints for the given device in the
                           current namespace
 -c, --no-canonicalize   don't canonicalize paths
 -d, --detach-loop       if mounted loop device, also free this loop device
     --fake              dry run; skip the umount(2) syscall
 -f, --force             force unmount (in case of an unreachable NFS system)
 -i, --internal-only     don't call the umount.<type> helpers
 -n, --no-mtab           don't write to /etc/mtab
 -l, --lazy              detach the filesystem now, clean up things later
 -O, --test-opts <list>  limit the set of filesystems (use with -a)
 -R, --recursive         recursively unmount a target with all its children
 -r, --read-only         in case unmounting fails, try to remount read-only
 -t, --types <list>      limit the set of filesystem types
 -v, --verbose           say what is being done

 -h, --help     display this help and exit
 -V, --version  output version information and exit

For more details see umount(8).

Usage:
 umount [-hV]
 umount -a [options]
 umount [options] <source> | <directory>

Options:
 -a, --all               unmount all filesystems
 -A, --all-targets       unmount all mountpoints for the given device in the
                           current namespace
 -c, --no-canonicalize   don't canonicalize paths
 -d, --detach-loop       if mounted loop device, also free this loop device
     --fake              dry run; skip the umount(2) syscall
 -f, --force             force unmount (in case of an unreachable NFS system)
 -i, --internal-only     don't call the umount.<type> helpers
 -n, --no-mtab           don't write to /etc/mtab
 -l, --lazy              detach the filesystem now, clean up things later
 -O, --test-opts <list>  limit the set of filesystems (use with -a)
 -R, --recursive         recursively unmount a target with all its children
 -r, --read-only         in case unmounting fails, try to remount read-only
 -t, --types <list>      limit the set of filesystem types
 -v, --verbose           say what is being done

 -h, --help     display this help and exit
 -V, --version  output version information and exit

For more details see umount(8).
BusyBox v1.19.4 (2014-10-20 19:21:55 CST) multi-call binary.

Usage: rmdir [OPTIONS] DIRECTORY...

argc = 6,  func = 178
argid[1]: 456; argv[1]: share
argid[2]: 637; argv[2]: save
argid[3]: 1170; argv[3]: "video"
argid[4]: 395; argv[4]: path
argid[5]: 1172; argv[5]: "/i-data/sysvol/video"
folder is not under mount point.
argc = 7,  func = 179
argid[1]: 456; argv[1]: share
argid[2]: 637; argv[2]: save
argid[3]: 1170; argv[3]: "video"
argid[4]: 395; argv[4]: path
argid[5]: 1172; argv[5]: "/i-data/sysvol/video"
argid[6]: 623; argv[6]: media-server
argc = 7,  func = 167
argid[1]: 456; argv[1]: share
argid[2]: 637; argv[2]: save
argid[3]: 1170; argv[3]: "video"
argid[4]: 395; argv[4]: path
argid[5]: 1172; argv[5]: "/i-data/sysvol/video"
argid[6]: 350; argv[6]: exit
share path /i-data/sysvol/video not existing.
share path /i-data/sysvol/photo not existing.
share path /i-data/sysvol/music not existing.
share path /i-data/sysvol/admin not existing.
share path /i-data/sysvol/video not existing.
share path /i-data/sysvol/photo not existing.
share path /i-data/sysvol/music not existing.
share path /i-data/sysvol/admin not existing.
RegenSmbConfigFile:2125 Close file ok
argc = 6,  func = 178
argid[1]: 456; argv[1]: share
argid[2]: 637; argv[2]: save
argid[3]: 1170; argv[3]: "photo"
argid[4]: 395; argv[4]: path
argid[5]: 1172; argv[5]: "/i-data/sysvol/photo"
folder is not under mount point.
argc = 7,  func = 179
argid[1]: 456; argv[1]: share
argid[2]: 637; argv[2]: save
argid[3]: 1170; argv[3]: "photo"
argid[4]: 395; argv[4]: path
argid[5]: 1172; argv[5]: "/i-data/sysvol/photo"
argid[6]: 623; argv[6]: media-server
argc = 7,  func = 167
argid[1]: 456; argv[1]: share
argid[2]: 637; argv[2]: save
argid[3]: 1170; argv[3]: "photo"
argid[4]: 395; argv[4]: path
argid[5]: 1172; argv[5]: "/i-data/sysvol/photo"
argid[6]: 350; argv[6]: exit
share path /i-data/sysvol/video not existing.
share path /i-data/sysvol/photo not existing.
share path /i-data/sysvol/music not existing.
share path /i-data/sysvol/admin not existing.
share path /i-data/sysvol/video not existing.
share path /i-data/sysvol/photo not existing.
share path /i-data/sysvol/music not existing.
share path /i-data/sysvol/admin not existing.
RegenSmbConfigFile:2125 Close file ok
argc = 6,  func = 178
argid[1]: 456; argv[1]: share
argid[2]: 637; argv[2]: save
argid[3]: 1170; argv[3]: "music"
argid[4]: 395; argv[4]: path
argid[5]: 1172; argv[5]: "/i-data/sysvol/music"
folder is not under mount point.
argc = 7,  func = 179
argid[1]: 456; argv[1]: share
argid[2]: 637; argv[2]: save
argid[3]: 1170; argv[3]: "music"
argid[4]: 395; argv[4]: path
argid[5]: 1172; argv[5]: "/i-data/sysvol/music"
argid[6]: 623; argv[6]: media-server
argc = 7,  func = 167
argid[1]: 456; argv[1]: share
argid[2]: 637; argv[2]: save
argid[3]: 1170; argv[3]: "music"
argid[4]: 395; argv[4]: path
argid[5]: 1172; argv[5]: "/i-data/sysvol/music"
argid[6]: 350; argv[6]: exit
share path /i-data/sysvol/video not existing.
share path /i-data/sysvol/photo not existing.
share path /i-data/sysvol/music not existing.
share path /i-data/sysvol/admin not existing.
share path /i-data/sysvol/video not existing.
share path /i-data/sysvol/photo not existing.
share path /i-data/sysvol/music not existing.
share path /i-data/sysvol/admin not existing.
RegenSmbConfigFile:2125 Close file ok
argc = 6,  func = 178
argid[1]: 456; argv[1]: share
argid[2]: 637; argv[2]: save
argid[3]: 1170; argv[3]: "admin"
argid[4]: 395; argv[4]: path
argid[5]: 1172; argv[5]: "/i-data/sysvol/admin"
folder is not under mount point.
argc = 7,  func = 167
argid[1]: 456; argv[1]: share
argid[2]: 637; argv[2]: save
argid[3]: 1170; argv[3]: "admin"
argid[4]: 395; argv[4]: path
argid[5]: 1172; argv[5]: "/i-data/sysvol/admin"
argid[6]: 350; argv[6]: exit
share path /i-data/sysvol/video not existing.
share path /i-data/sysvol/photo not existing.
share path /i-data/sysvol/music not existing.
share path /i-data/sysvol/admin not existing.
share path /i-data/sysvol/video not existing.
share path /i-data/sysvol/photo not existing.
share path /i-data/sysvol/music not existing.
share path /i-data/sysvol/admin not existing.
RegenSmbConfigFile:2125 Close file ok
argc = 4,  func = 402
argid[1]: 1248; argv[1]: yes
argid[2]: 1249; argv[2]: yes
argid[3]: 1250; argv[3]: yes
argc = 1,  func = 360
TELNET start success!
argc = 2,  func = 148
argid[1]: 1156; argv[1]: 15
killall: hd-idle: no process killed
test0
Test1
Test2
Test3:
argc = 2,  func = 151
argid[1]: 1157; argv[1]: 50
test0
Test1
Test2
Test3:
argc = 2,  func = 662
argid[1]: 1088; argv[1]: ge1
Oct 22 11:36:34 (none) httpd[1887]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache]
Oct 22 11:36:34 (none) httpd[1887]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Oct 22 11:36:34 (none) httpd[1887]: [warn] RSA server certificate CommonName (CN) `NAS540' does NOT match server name!?
Oct 22 11:36:34 (none) httpd[1887]: [error] mod_auth_zyxel: initialized.
argc = 2,  func = 162
argid[1]: 1161; argv[1]: d
exec_cmd complete
eth status = d 
ethtest0
Test1
Test2
Test3:
argc = 2,  func = 164
argid[1]: 1162; argv[1]: enable
sh: can't create /proc/LEDBlinkStatus: nonexistent directory
argc = 2,  func = 524
argid[1]: 934; argv[1]: activate
/bin/killall -USR1 app_wd
killall: app_wd: no process killed
argc = 2,  func = 18
argid[1]: 350; argv[1]: exit
argc = 1,  func = 20
[1537] is disconnected
[1900] server write-only FIFO is opened (fd=6)
[1900] server read-only FIFO is opened (fd=7)
[1900] server error read-only FIFO is opened (fd=8)
argc = 2,  func = 679
argid[1]: 1392; argv[1]: remove
/bin/rm -f /tmp/iface_lock_file
[1900] is disconnected
Oct 22 11:36:36 (none) httpd[1914]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache]
Oct 22 11:36:36 (none) httpd[1914]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Oct 22 11:36:36 (none) httpd[1914]: [warn] RSA server certificate CommonName (CN) `NAS540' does NOT match server name!?
Oct 22 11:36:36 (none) httpd[1914]: [error] mod_auth_zyxel: initialized.
configure terminal ip smb internal disable ""
[1928] server write-only FIFO is opened (fd=6)
[1928] server read-only FIFO is opened (fd=7)
[1928] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 185
argid[1]: 641; argv[1]: internal
argid[2]: 303; argv[2]: disable
argid[3]: 1184; argv[3]: ""
share path /i-data/sysvol/video not existing.
share path /i-data/sysvol/photo not existing.
share path /i-data/sysvol/music not existing.
share path /i-data/sysvol/admin not existing.
share path /i-data/sysvol/video not existing.
share path /i-data/sysvol/photo not existing.
share path /i-data/sysvol/music not existing.
share path /i-data/sysvol/admin not existing.
RegenSmbConfigFile:2125 Close file ok
[1928] is disconnected
Starting smbd...
Oct 22 11:36:37 (none) httpd[1919]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Oct 22 11:36:37 (none) httpd[1919]: [warn] RSA server certificate CommonName (CN) `NAS540' does NOT match server name!?
Oct 22 11:36:37 (none) httpd[1919]: [error] mod_auth_zyxel: initialized.
Starting nmbd...
Starting NSU Agent...
Starting AFP... avahi-daemonOct 22 11:36:38 (none) avahi-daemon[2009]: Found user 'admin' (UID 501) and group 'everyone' (GID 500).
Oct 22 11:36:38 (none) avahi-daemon[2009]: Successfully dropped root privileges.
Oct 22 11:36:38 (none) avahi-daemon[2009]: avahi-daemon 0.6.31 starting up.
Oct 22 11:36:38 (none) avahi-daemon[2009]: WARNING: No NSS support for mDNS detected, consider installing nss-mdns!
Oct 22 11:36:38 (none) avahi-daemon[2009]: Loading service file /etc/avahi/services/afp.service.
Oct 22 11:36:38 (none) avahi-daemon[2009]: Joining mDNS multicast group on interface egiga1.IPv4 with address 192.168.111.43.
Oct 22 11:36:38 (none) avahi-daemon[2009]: New relevant interface egiga1.IPv4 for mDNS.
Oct 22 11:36:38 (none) avahi-daemon[2009]: Network interface enumeration completed.
Oct 22 11:36:38 (none) avahi-daemon[2009]: Registering new address record for 192.168.111.43 on egiga1.IPv4.
Oct 22 11:36:38 (none) avahi-daemon[2009]: Registering HINFO record with values 'ARMV7L'/'LINUX'.
 netatalk.
Oct 22 11:36:38 (none) netatalk[2048]: Netatalk AFP server starting
Oct 22 11:36:38 (none) netatalk[2048]: Registered with Zeroconf
There is no usable system volume! Do nothing...
/ram_bin/etc/init.d/rcS2: line 382: /usr/bin/zyfw_ac_trigger: not found
Oct 22 11:36:39 (none) cnid_metad[2061]: CNID Server listening on localhost:4700
GMT offset=7200s
setting system time zone to tz_minuteswest=-120
Oct 22 11:36:39 (none) avahi-daemon[2009]: Server startup complete. Host name is NAS540.local. Local service cookie is 3230063189.
There is no sysvol
[2146] server write-only FIFO is opened (fd=6)
[2146] server read-only FIFO is opened (fd=7)
[2146] server error read-only FIFO is opened (fd=8)
argc = 2,  func = 339
argid[1]: 1224; argv[1]: former
[2146] is disconnected
Oct 22 11:36:40 (none) avahi-daemon[2009]: Service "NAS540 (AFP)" (/etc/avahi/services/afp.service) successfully established.
schedule_controller is already running now.
Starting "/etc/init.d/zypkg_controller.sh".
Starting to set up zy-pkgs environment ...
-> No volume exists now. zy-pkgs will not work.
sh: you need to specify whom to kill
Oct 22 11:36:40 (none) syslog-ng[1478]: Termination requested via signal, terminating; 
Oct 22 11:36:40 (none) syslog-ng[1478]: syslog-ng shutting down; version='2.0.10'
Oct 22 11:36:40 NAS540 syslog-ng[2340]: syslog-ng starting up; version='2.0.10'
rm: can't remove '/i-data/.system/dropbox/dropbox.enable': No such file or directory
mkdir: can't create directory '/i-data/.system/dropbox': No such file or directory
cp: can't create '/i-data/.system/dropbox/dropbox.db': No such file or directory
setLED COPY OFF
led_state_map_addr = 50
chmod: /usr/local/apache/web_framework/data/cache: Read-only file system
chmod: /usr/local/apache/web_framework/data/cache: Read-only file system
Web Server already started.
Starting app_wd...
[2644] server write-only FIFO is opened (fd=6)
[2644] server read-only FIFO is opened (fd=7)
[2644] server error read-only FIFO is opened (fd=8)
argc = 2,  func = 677
argid[1]: 382; argv[1]: status
[2644] is disconnected
#[033mPower on HD1 ...#[0m
#[033mPower on HD2 ...#[0m
#[033mPower on HD3 ...#[0m
#[033mPower on HD4 ...#[0m
#[031m core_checksum #[0m: c357af76ee3c581f64d71989a647a5cc
#[031m fwversion #[0m: V5.00(AATB.0)b8
#[031m img_checksum #[0m: bba0930a1c080b56754403eb3ef98647
#[031m modelid #[0m: B103
#[031m revision #[0m: 45048
#[031m romfile_checksum #[0m: 71BD
#[031m zld_checksum #[0m: 638763671ceeb1be5dc07fb007d868cb
Update zypkg list
[2684] server write-only FIFO is opened (fd=6)
[2684] server read-only FIFO is opened (fd=7)
[2684] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 640
[2684] is disconnected
cmd_name = download
[2715] server write-only FIFO is opened (fd=6)
[2715] server read-only FIFO is opened (fd=7)
[2715] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 400
killall: twonkystarter: no process killed
Oct 22 11:36:44 NAS540 smbd[2736]: [2014/10/22 11:36:44.238621,  0] ../source3/printing/print_standard.c:68(std_pcap_cache_reload)
Oct 22 11:36:44 NAS540 smbd[2736]:   Unable to open printcap file /etc/printcap for read!
ls: /i-data/.system/zy-pkgs/USERZYPKG_*: No such file or directory
umount: /usr/local/apache/htdocs/adv,/res/imdb_poster: not mounted
[2715] is disconnected
rm: can't remove '/etc/zyxel/webdav/dav.flag': No such file or directory
rm: can't remove '/etc/zyxel/webdav/dav_anonymous.flag': No such file or directory
#LoadModule dav_module      /usr/local/apache/modules/mod_dav.so
Oct 22 11:36:55 NAS540 httpd[2790]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache]
Oct 22 11:36:55 NAS540 httpd[2790]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Oct 22 11:36:55 NAS540 httpd[2790]: [warn] RSA server certificate CommonName (CN) `NAS540' does NOT match server name!?
Oct 22 11:36:55 NAS540 httpd[2790]: [error] mod_auth_zyxel: initialized.
rm: can't remove '/tmp/dav_processing.flag': No such file or directory
WebDAV is disable!
===> Generate zysync server config ...
     ===> Generating volume list ...
     ===> Generating zysync config file ...
rm: can't remove '/tmp/zysync_modules': No such file or directory
===> Starting zysync server ...
[INFO]: Starting server mode ... 

Done
===> Generating stunnel server config file ...
===> Starting stunnel server ...
[.] stunnel 5.02 on arm-unknown-linux-gnu platform
[.] Compiled/running with OpenSSL 1.0.0g 18 Jan 2012
[.] Threading:FORK Sockets:POLL,IPv6 SSL:ENGINE,OCSP
[ ] errno: (*__errno_location ())
[.] Reading configuration from file /etc/zyxel/BackupPlanner/stunnel/stunneld.conf
[ ] Compression disabled
[ ] PRNG seeded successfully
[ ] Initializing service [szysync]
[ ] Loading cert from file: /etc/zyxel/BackupPlanner/zysync/zysync.cert
[!] error queue: 140DC002: error:140DC002:SSL routines:SSL_CTX_use_certificate_chain_file:system lib
[!] error queue: 20074002: error:20074002:BIO routines:FILE_CTRL:system lib
[!] SSL_CTX_use_certificate_chain_file: 2001002: error:02001002:system library:fopen:No such file or directory
[!] Service [szysync]: Failed to initialize SSL context
Done
led_state_map_addr = 46

Please press Enter to activate this console. Oct 22 11:36:56 NAS540 httpd[2795]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Oct 22 11:36:56 NAS540 httpd[2795]: [warn] RSA server certificate CommonName (CN) `NAS540' does NOT match server name!?
Oct 22 11:36:56 NAS540 httpd[2795]: [error] mod_auth_zyxel: initialized.
Oct 22 11:37:03 NAS540 afpd[2058]: Netatalk AFP/TCP listening on 192.168.111.43:548
[2938] server write-only FIFO is opened (fd=6)
[2938] server read-only FIFO is opened (fd=7)
[2938] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 70
[2938] is disconnected
[2945] server write-only FIFO is opened (fd=6)
[2945] server read-only FIFO is opened (fd=7)
[2945] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 71
/usr/sbin/zic -d /etc /var/zyxel/myzone_rule
/bin/ln -s -f /etc/MyZone /etc/localtime
[2945] is disconnected
Oct 22 11:38:02 NAS540 ntpdate[2957]: adjust time server 88.198.92.72 offset 0.006106 sec
[2963] server write-only FIFO is opened (fd=6)
[2963] server read-only FIFO is opened (fd=7)
[2963] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 337
[2963] is disconnected
[2987] server write-only FIFO is opened (fd=6)
[2987] server read-only FIFO is opened (fd=7)
[2987] server error read-only FIFO is opened (fd=8)
argc = 1,  func = 337
[2987] is disconnected
[2994] server write-only FIFO is opened (fd=6)
[2994] server read-only FIFO is opened (fd=7)
[2994] server error read-only FIFO is opened (fd=8)
argc = 4,  func = 334
argid[1]: 1222; argv[1]: ""
argid[2]: 599; argv[2]: in
argid[3]: 1223; argv[3]: "Amsterdam,Berlin,Bern,Rome,Stockholm,Vienna"
[2994] is disconnected
[  518.083404] PHY: comcerto-0:06 - Link is Down
[  518.087791] pfe_eth_adjust_link: PHY: comcerto-0:06, phy->link: 0
/sbin/egiga_link_down.sh ...
Oct 22 11:43:50 NAS540 avahi-daemon[2009]: Withdrawing address record for 192.168.111.43 on egiga1.
Oct 22 11:43:50 NAS540 avahi-daemon[2009]: Leaving mDNS multicast group on interface egiga1.IPv4 with address 192.168.111.43.
Oct 22 11:43:50 NAS540 avahi-daemon[2009]: Interface egiga1.IPv4 no longer relevant for mDNS.
Oct 22 09:43:51 NAS540 dhcpcd[1672]: terminating on signal 1